Tshare XE320D-C PUR Single-Color Glue Machine Constant Temperature Glue Supply for Edge Banding

Need PUR edge gluing that keeps up with a fast edge banding line? The XE320D-C is a single-color PUR hot melt glue machine that melts at 185 °C, holds ±2 °C and supplies adhesive at up to 3000 m/h with no breakpoints. It runs a 20 kg (5 gallon) drum at 0.5 L/min flux, draws 4.5 kW and measures 1012 × 475 × 1350 mm. The supply path is fully sealed and one-way, so there is no cleaning between drums, and the sealed circuit saves up to 30% glue and energy.

Three things slow an automatic edge banding line: adhesive that reaches the glue unit unevenly and leaves breakpoints in the bead, glue temperature that drifts far enough to change the joint, and a pot that has to be drained and scraped between shifts. The XE320D-C removes all three.

It is a single-color PUR hot melt glue machine for edge banding machines. Adhesive is melted and held at 185 °C, metered at 0.5 L/min and delivered at up to 3000 m/h with no breakpoints, so the supply keeps pace with a high-speed automatic line instead of capping its feed speed. Temperature is held to ±2 °C, which keeps a PUR bead the same width on the first panel of a shift and the last.

Glue is loaded as a 5 gallon (20 kg) drum and fed through a fully sealed, one-way circuit: adhesive leaves the drum, reaches the platen and never returns, so the circuit is not opened or cleaned between drums. Capacity and sealed delivery save up to 30% in adhesive and heating energy.

The unit draws 4.5 kW, works on 0.6 MPa shop air and stands on a 1012 × 475 × 1350 mm frame. It feeds KDT, NANXING, HOMAG and most automatic edge banding machines, on panel closets, kitchen cabinets, bookcases and desks.

Eight points a maintenance team can check against the machine and its drums.

• 3000 m/h glue supply — adhesive reaches the edge gluing device at up to 3000 m/h with no breakpoints, so supply matches a high-speed automatic line.
• ±2 °C temperature control — melt and hose temperature are held to ±2 °C around an 185 °C setpoint, so bead width stays constant across a shift.
• Fully sealed one-way supply — glue travels drum to platen only; nothing returns, so the circuit needs no cleaning when a drum runs out.
• 20 kg drum capacity — one 5 gallon (20 kg) drum sits on the machine, so a shift of production needs fewer glue changes.
• 0.5 L/min metered flux — glue is delivered at a fixed 0.5 L/min and switched by an infrared sensor, so the bead follows line speed.
• Up to 30% glue and energy saving — sealed delivery plus constant temperature cut adhesive and heating energy by up to 30% against an open pot.
• Aluminium platen, rubber drum gasket — the aluminium alloy platen and its solid silicone ring seal the drum, and the gasket is dimensioned to the drum bottom so no glue is left behind.
• Fool-proof controls, 4.5 kW drive — the sequence is guarded against wrong-step use, and the 4.5 kW drive sits on a castor-mounted 1012 × 475 × 1350 mm frame.

An edge bander running PUR has two bad options today: keep an open glue pot and absorb the breakpoints, cleaning time and glue waste, or send panels out. This machine is the third option.

• Output that matches the line. At up to 3000 m/h with no breakpoints, glue supply stops being the reason a high-speed bander runs below its rated feed speed.
• A joint that looks the same at both ends of a shift. ±2 °C control around 185 °C keeps bead geometry constant, so panels from hour eight match panels from hour one.
• Up to 30% less glue and energy. A sealed one-way circuit and constant temperature cut both adhesive consumption and heating load, and the saving repeats every shift, not once.
• No cleaning between drums. Because nothing returns to the drum, the circuit is not opened and scraped at every glue change — that maintenance hour goes back to production.
• More of each drum reaches the panel. The rubber gasket is dimensioned to the drum bottom, so the last of the 20 kg charge is delivered instead of being thrown out with the drum.
• A drum change that stays mechanical. 20 kg in a drum, a platen lifted on 0.6 MPa air and a 1012 × 475 × 1350 mm castor-mounted frame keep the swap a one-person job at the machine.

Yes, if your machine is an automatic edge banding machine. The unit is built for edge banding machines and is used with KDT, NANXING, HOMAG and most other automatic lines. Confirm your glue type and the machine interface before ordering, because the machine is a single-color PUR unit, not a universal glue pot.

Single-color PUR hot melt adhesive, melted at 185 °C. One drum holds one adhesive, so the machine is for single-color production — there is no second channel and no colour change inside the machine.

Up to 3000 m/h with no breakpoints. Flux is 0.5 L/min and glue is switched by an infrared sensor, so the supply follows the line instead of running empty at the glue unit.

±2 °C, with an 185 °C melt setpoint. An intelligent thermostatic hose and infrared-sensor glue supply hold that band along the whole path from drum to platen, which is what stops temperature-driven breakpoints.

No. The supply is fully sealed and one-way: adhesive goes from drum to platen and never returns, so the circuit is not opened or cleaned when you change drums.

5 gallons, 20 kg, per drum, and the saving covers both adhesive and energy — up to 30%. It comes from sealed one-way delivery and from holding temperature instead of reheating an open pot.

0.6 MPa compressed air. Air drives the platen that lands on the drum, and the aluminium alloy platen with its silicone sealing ring is what closes the drum and holds the seal while glue is pushed out.

1012 × 475 × 1350 mm and 4.5 kW. The unit stands on castors beside the bander, so it can be moved between lines, and the rubber drum gasket keeps the drum bottom clear of leftover adhesive.