Polishing Wheels For Edgebander 180x50x20mm Edge Banding Machine Spare Parts

Need a replacement polishing wheel that goes straight onto the buffing shaft of your edge banding machine? The BW015 is a cotton cloth wheel measuring φ180 mm outside diameter, φ50 mm centre hole and 20 mm thick, so the three numbers a shaft actually cares about are fixed before you order. The 20 mm cloth face carries polishing compound across the trimmed edge instead of dropping it in patches. It ships in a carton box, and other diameters, thicknesses and centre hole shapes can be supplied on request.

Every edge banding machine stops producing the moment its polishing wheel stops polishing. Three things go wrong in the same order: the cloth face wears down and no longer reaches the trimmed edge, the replacement arrives with the wrong outside diameter or bore, and somebody starts dressing the old wheel by hand to get through the shift. The BW015 stops that third one.

It is a cotton cloth polishing wheel for the finishing station of an edge banding machine, and three measurements define it: φ180 mm outside diameter, φ50 mm centre hole and 20 mm thickness. The cotton cloth sits on a metal centre, so the 50 mm bore is metal where the shaft grips, and the cloth face holds polishing compound instead of letting it run off the rim.

The 20 mm face spans banding widths up to 20 mm, which covers the edge of most cabinet panels in one pass rather than two overlapping ones. The polishing station sits after the trimming cutters, so the wheel works on the edge they have just finished and brings the banding up to an even sheen.

Packing is a carton box. Other diameters, thicknesses and centre hole shapes can be supplied on request. Match the three numbers above to your shaft and the part fits as a direct replacement.

Each line below is a dimension or a material fact you can check on the wheel before it goes on the shaft.

• φ180 mm outside diameter — the face that meets the edge is 180 mm across, so the wheel matches shafts built for that size.
• φ50 mm centre hole — a straight 50 mm bore slides onto the buffing shaft without an adapter bush.
• 20 mm face width — spans banding widths up to 20 mm, so the trimmed edge is covered in one pass.
• Cotton cloth face — the cloth holds polishing compound and spreads it across the edge rather than dropping it in patches.
• Metal centre — the cloth sits on a metal centre, so the 50 mm bore is metal where the shaft grips.
• Finishing-station part — replaces the worn polishing wheel on a CNC edge banding machine and runs on the edge the trimming cutters have just finished.
• One-nut change — the wheel comes off and goes back on with the shaft nut, so a worn face is swapped without touching cutter settings.
• Carton box packing — the wheel is supplied in a carton box, so the cloth face is not loose against other parts.
• Other sizes available — different diameters, thicknesses and centre hole shapes can be supplied, so 180 × 50 × 20 mm is not the only option.

The usual choice is between running a worn wheel until edges start failing inspection and ordering a part that does not fit the shaft. The BW015 settles the second question with three numbers.

• Fit is three numbers, not a guess. 180 mm outside diameter, 50 mm bore, 20 mm thickness — measure your shaft, compare, order. No adapter bush and no shimming.
• Edges leave the line finished. Polishing is the last station, so panels reach packing with an even sheen instead of being pulled aside for hand work.
• The whole band gets covered. A 20 mm face is wider than the banding on most cabinet panels, so the operator does not have to work the wheel up and down the edge.
• The change fits inside a normal stop. One nut, one shaft, one wheel: the worn face is off and the new one is on before the next panel reaches the station.
• Nothing else on the machine moves. Trimming cutters, feed and glue pot stay where they are; only the polishing wheel is replaced.
• A different shaft is not a dead end. Other diameters, thicknesses and centre hole shapes can be supplied on request.

It fits the polishing station of a CNC edge banding machine. The wheel is a φ180 mm outside diameter, φ50 mm bore, 20 mm thick cotton cloth part, so what decides the fit is your buffing shaft, not the machine brand.

φ180 mm outside diameter, φ50 mm centre hole, 20 mm thickness. Those three numbers are the whole size specification — check them against the shaft before ordering.

Cotton cloth on a metal centre. The cloth face carries the polishing compound against the edge, and the metal centre holds the 50 mm bore where the shaft grips.

Yes, but not in this exact size. The standard BW015 has a φ50 mm centre hole; other sizes and centre hole shapes can be supplied on request, so send the bore and thickness your shaft needs.

Up to 20 mm in a single pass. The 20 mm face width covers the banding widths used on most cabinet panels without working the wheel up and down.

Take the old wheel off its shaft and slide the new one on. The bore is a straight φ50 mm hole, so there is no adapter bush to line up before the shaft nut is tightened.

In a carton box. Carton box is the standard packing for this wheel; if you order several sizes at once, say so so packing can be arranged before shipment.

Contact us with the quantity and the size you need. Price depends on order quantity and on whether you take the standard 180 × 50 × 20 mm size or a custom bore and thickness.