Servo Pre-Milling Unit for Edgebanding Machine Edgebander Milling Unit

Need one pre-milling unit that holds the same cut depth from the first panel to the last? The XEZG-A is a servo-driven pre-milling unit that mounts vertically on an edgebander base, ahead of the glue pot, and mills both panel faces before the band goes on. It covers 10–60 mm panel thickness and panels with narrow length from 80 mm, at 0–30 m/min feeding speed and 0.2–0.5 MPa working pressure. Overall dimensions are L365 × W500 × H512 mm. Cutting allowance is dialled in as a number on the panel, not tapped in by feel.

Edge chipping that only shows after the band is pressed on, a pre-milling head that drifts out of adjustment mid-shift, and chips packing the housing until the line has to stop: the XEZG-A servo pre-milling unit is built around those three failures. It handles panels from 10 mm to 60 mm.

It is a milling unit, not a complete edgebander. It mounts vertically on the edgebander base ahead of the glue pot and removes edge material from both faces, so the band bonds to a flat, straight surface instead of a chipped one. Two tracking shoes ride the panel and correct deviation in real time, keeping panels as narrow as 80 mm on the cutter line.

Cutting position and depth come from a servo motor turning a lead screw that moves the front guide plate, so allowance is set as a number on the digital adjustment panel, not by feel on a hand wheel. Cutter height works the same way. Two spindle nuts set pre-load pressure and cutter oscillation range separately, which keeps vibration down while the head oscillates.

The housing is enclosed, and chips leave through a directional extraction port rather than falling into the unit. Feeding speed runs 0–30 m/min at 0.2–0.5 MPa working pressure. Overall dimensions are L365 × W500 × H512 mm. Customization is supported.

What separates this unit from a hand-adjusted pre-milling head is the setting mechanism and the guide arrangement, not the footprint:

• Servo-driven depth setting — a lead screw moves the front guide plate, so allowance is dialled in as a number instead of tapped in by hand.
• Double-guide tracking — two shoes ride the panel and correct deviation in real time, holding panels from 80 mm narrow length upward.
• 10–60 mm range — the same unit is specified for panels from 10 mm up to 60 mm thick, so thin and thick work stay on one head.
• Digital adjustment panel — cutter height is set by displayed value, so the same setting can be repeated at the start of the next shift.
• Dual-nut spindle — nut one sets pre-load pressure, nut two sets cutter oscillation range, which keeps the shaft steady while the head cuts.
• Directional chip extraction — an enclosed housing with a directional port sends chips away from the panel instead of into the frame.
• Feeding to 30 m/min — the unit is specified for a line running 0–30 m/min at 0.2–0.5 MPa working pressure.
• Vertical base mounting — it fits the edgebander base ahead of the glue pot in L365 × W500 × H512 mm of space.
• Customization supported — bracket and cutter configuration can be built to the machine it is going on.

The choice is usually between sending pre-milling work out, running a hand-adjusted head and living with the drift, or buying a whole new edgebander:

• A repeatable edge, not a feel-based one. The allowance is a number on a display, so the panel milled at the start of the shift matches the one milled at the end of it.
• Fewer stops for chip build-up. The cutter oscillates and the housing is enclosed with a directional extraction port, so the chip path stays open across the 0–30 m/min feeding range.
• Narrow panels stay on line. Two tracking shoes hold 80 mm narrow panels against the cutter, which is where a single-guide head usually lets go.
• Thickness changes are setting changes. Panels from 10 mm to 60 mm run on the same unit, so a mixed order does not need a head swap.
• One unit, one install. It mounts on the edgebander base ahead of the glue pot and takes L365 × W500 × H512 mm, so the upgrade stays inside the machine frame.
• Built to the machine you already run. Customization is supported, so the bracket and cutter set are matched to that edgebander instead of the other way round.
• A quote before a commitment. Price is quoted against your panel thickness range and feeding speed, so nothing is assumed about your line.

10 mm to 60 mm. That is the thickness range the unit is specified for, with the cutter set to the top and bottom edge of the panel before the band is applied.

Only if the machine takes a vertical, base-mounted pre-milling unit. Installation is vertical on the edgebander base ahead of the glue pot, and the unit needs L365 × W500 × H512 mm of space, so measure that first.

From the adjustment panel, by servo. A servo motor turns a lead screw that moves the front guide plate, so allowance is set as a number on the digital display instead of being tapped in on a hand wheel.

Yes, down to 80 mm narrow panel length. Two tracking shoes ride the panel and correct deviation in real time, which is what keeps a narrow panel against the cutter.

An enclosed housing with a directional extraction port, plus an oscillating cutter. Chips are directed out of the unit instead of packing behind the cutter, which is where a fixed head usually jams.

0.2–0.5 MPa. The unit runs at that working pressure and feeds at 0–30 m/min, so it follows the line speed instead of setting it.

No. It is the pre-milling unit only, installed on the edgebander base before the glue pot; the glue pot, pressure rollers and end-trimming units stay on your own machine.

Customization is supported, and the price is quoted per configuration. Send the edgebander model, the panel thickness range and the feeding speed you run, and the quotation is built against those three numbers.