Premelting Glue Device with Large Capacity 8kg EVA Glue Premelting Device Fast Melting

Need an edgebanding machine that runs a full shift without stopping to refill glue? The XE-YR-B premelting glue unit holds 8 kg of EVA in one load and preheats in 3 minutes. It melts and feeds at 18 L/h with working pressure 0.2 – 0.5 MPa from a 2100 W heating system, has a real-time level sensor and one-button discharge, and installs vertically on the machine upper beam at L520 × W190 × H780 mm. A conventional glue pot holds about 1.5 kg per refill.

A dry glue pot stops an edgebanding line more often than any other fault. A conventional pot holds roughly 1.5 kg of EVA per refill, so the operator leaves the panel flow repeatedly, and the board that arrives while the pot is cold takes a thin bead or none. The XE-YR-B premelting glue unit takes that cycle out of the shift.

It is a high-capacity premelting glue unit that mounts vertically on the upper beam of an edgebanding machine and melts EVA before the glue reaches the application roller. One load holds 8 kg. The tank is wrapped in multi-layer insulation, a level sensor watches the melt, and one button discharges residue at cleaning time.

Heating is rated 2100 W, enough to reach working temperature within 3 minutes, after which it melts and feeds without pause. Delivery runs at 18 L/h at a working pressure of 0.2 – 0.5 MPa, so bead width holds on a short custom batch and at flat out.

The body measures L520 × W190 × H780 mm, vertical, inside the machine envelope rather than on the floor beside it. On high-volume or custom furniture batches the gain shows up as refills not made and stops not taken.

Nine details decide whether a premelter earns its place on a busy line:

• 3-minute preheat – A 2100 W heating system reaches working temperature in 3 minutes, so the first board of a shift is glued, not queued.
• 8 kg tank – One load carries 8 kg of EVA against roughly 1.5 kg in a conventional pot; refills drop to one per shift.
• 18 L/h feed – Glue leaves at 18 L/h under 0.2 – 0.5 MPa, keeping bead width steady at low and high feed rates.
• Steady output – Melt level and temperature stay constant, so bond strength on the last board matches the first.
• Multi-layer insulation – Layered tank walls hold heat in the melt instead of radiating it into the frame, and the outer surface stays cooler.
• Anti-clogging path – The glue route keeps melt moving, so carbonised residue cannot settle at the outlet and stall a run.
• Real-time level sensing – Sensors read the glue level continuously, so nobody refills on guesswork and the heater never dry-cycles.
• One-button discharge – One control empties the tank for cleaning or a change of adhesive, with no scraping and no cooling wait.
• Vertical upper-beam mount – At L520 × W190 × H780 mm the unit hangs on the upper beam, inside the machine footprint.

A shop whose glue pot cannot keep up has two choices: keep stopping the line, or buy another machine. This unit removes the choice by moving the bottleneck off the line.

• One refill where there were several. 8 kg per load against about 1.5 kg in a conventional pot means the operator stays at the machine instead of walking to the tank.
• The bond stops depending on timing. A cold pot gives a thin bead; with 3 minutes to temperature and a level sensor watching the melt, glue arrives ready on every board.
• Downtime moves to the cleaning window. The anti-clogging path and steady 18 L/h flow keep the line running through a batch rather than stopping somewhere in the middle of it.
• Cleaning costs a button press. Discharge is powered, so the tank empties without scraping and without waiting for the melt to cool down first.
• Less material re-melted twice. Level sensing stops the heater from working an empty tank, which is where EVA browns and has to be thrown away.
• It fits the machine you already own. L520 × W190 × H780 mm on the upper beam, vertical: no extra floor space and no second line.
• Built for the long run. High-volume and custom furniture batches get the same bead on the last board of the shift as on the first.

It melts the glue before it is used and holds far more of it. One load carries 8 kg against roughly 1.5 kg in a conventional pot, and the melt is fed from the unit at 18 L/h rather than being drawn straight from a heated tank.

8 kg per load, which the specification allows for continuous operation through a shift without refilling. The 18 L/h figure is the feed rate the unit delivers, not the amount a line consumes.

3 minutes from cold to working temperature, from a 2100 W heating system. After that the unit keeps melting and feeding with no further wait.

Yes, if the machine has a free upper beam. The unit installs vertically, measures L520 × W190 × H780 mm, and is supplied as an edge banding machine spare part rather than as part of a new line.

18 L/h at a working pressure of 0.2 – 0.5 MPa. That range covers both slow custom runs and full-speed production without changing the bead width.

Blockage is designed out rather than cleaned up afterwards. The glue path keeps the melt moving so carbonised residue cannot settle at the outlet and stop the run.

Press the discharge control. One-button discharge empties the tank while the glue is still warm, so there is no scraping and no cooling wait before a change of adhesive.

Price is quoted per order, not fixed on the page. Send your edgebanding machine model and the quantity you need and a quotation follows; MOQ, lead time, payment terms and packing are confirmed in that quotation.