4-006-01-0063 4006010063 Deep Groove Ball Bearing FAG 6002-2RSR-C3 DIN 625 6002

When a bearing on a Homag machine starts to rumble or seize, the spindle or feed axis stops cutting accurately and the machine may fault out. This 6002.2RSR.C3 bearing addresses that failure by replacing the worn unit with a sealed, clearance-controlled bearing that keeps dust out and maintains running clearance.

The bearing is a deep groove ball bearing with a 15mm inner diameter, 32mm outer diameter, and 9mm thickness. It meets DIN 625 and carries the model number 6002. FAG is the brand, and the Homag part number is 4006010063 or 4-006-01-0063. To confirm the fit, compare these dimensions and the part number against your machine's manual or the old bearing.

Check the shaft and housing for wear before pressing the new bearing on. The 2RSR suffix means two rubber seals, one on each side, which block wood dust and chips from entering the raceway. The C3 suffix indicates a radial internal clearance larger than standard, which helps when the bearing runs warm in a machine tool spindle.

Supply comes as the bearing alone; no packaging, customisation, or additional parts are included unless you ask. When enquiring, send the Homag part number 4006010063 or 4-006-01-0063, the model 6002, and the dimensions 15mm x 32mm x 9mm so the supplier can match the exact bearing.

What the specification fixes, and what it leaves to the machine:

• Seal protection against wood dust — Two rubber seals, one on each side, keep wood dust and chips out of the raceway on Homag machines.
• Clearance for warm running — The C3 internal clearance gives extra room for expansion when the bearing runs warm in a spindle.
• Standardised boundary dimensions — DIN 625 sets the boundary dimensions, so the 15mm bore and 32mm outer diameter fit standard housings.
• Direct Homag number match — The Homag number 4006010063 or 4-006-01-0063 lets you match the bearing to the machine's parts list.
• FAG 6002 model identification — The 6002 model number identifies the bearing size and type, making cross-reference straightforward at the parts counter.
• Compact 9mm width — A 9mm thickness keeps the bearing narrow, fitting tight axial spaces in woodworking machine assemblies.
• Deep groove load support — Deep groove geometry supports radial and axial loads, which suits the combined loads in feed and spindle drives.
• Pressed fit on 15mm shaft — The 15mm inner diameter presses onto a 15mm shaft, a common size for small bearing seats in machine tools.
• Sealed-for-life lubrication — The rubber seals retain the factory grease, so no relubrication is needed during the bearing's service life.

What changes on the shop floor once the unit is in place:

• Seals keep dust out. Wood dust is the main cause of bearing failure on woodworking machines; the two rubber seals block it, so the bearing lasts longer between replacements.
• C3 clearance handles heat. Machines run warm, and the C3 clearance gives room for expansion, reducing the risk of seizure and keeping the bearing running smoothly.
• Exact Homag number match. You can order by the Homag number 4006010063 or 4-006-01-0063, so there is no guesswork about which bearing fits your machine.
• DIN 625 dimensional confidence. The DIN 625 standard means the 15mm bore, 32mm outer diameter, and 9mm width are held to a known tolerance, so the bearing fits the housing.
• FAG brand recognition. FAG is a known bearing brand, so you can cross-reference the 6002 model number with existing stock or maintenance records.
• Compact size for tight spaces. At 9mm thick, the bearing fits into narrow assemblies where a wider bearing would not go, simplifying retrofit work.
• Sealed grease saves maintenance. Because the seals keep the grease in, you do not need to relubricate, cutting maintenance time on each spindle or feed axis.

Check your machine's parts manual for the number 4006010063 or 4-006-01-0063 and confirm the 15mm bore, 32mm outer diameter, and 9mm width match the old bearing.

2RSR means two rubber seals, one per side, and C3 means radial internal clearance larger than standard, which helps when the bearing runs warm.

It is sealed: the 2RSR suffix indicates rubber seals on both sides, which block dust and retain grease.

The inner diameter is 15mm, the outer diameter is 32mm, and the thickness is 9mm, to DIN 625.

Yes, if the shaft is 15mm, the housing bore is 32mm, and the width is 9mm, the bearing will fit any application needing a 6002.2RSR.C3.

Send the Homag part number 4006010063 or 4-006-01-0063, the model 6002, and the dimensions 15mm x 32mm x 9mm, plus the quantity you need.

No, the bearing is supplied as a single unit without instructions; installation should follow your machine manual or standard bearing fitting practice.

C3 clearance is intended for applications where the bearing runs warm, such as machine tool spindles, and it helps prevent seizure at speed.