3 Flutes Spiral Coated Fine End Mill for Multi layer Board Plywood Density Board

A 3-flute spiral coated fine end mill for woodworking CNC machines, built to cut multi-layer board, plywood and density board. It is made from alloy and runs at high processing speed with easy discharge and low processing noise. Diameter runs D6 to D22; total length runs 90 to 120mm. The SKU 10X50X10X100 shown in the pictures gives you one size to check against your spindle and collet before ordering.

Fuzzy edges and torn faces on multi-layer board usually come from a cutter that cannot clear chips fast enough. When chips pack the flutes, heat builds, the edge dulls, and the finish drops. A 3-flute spiral coated fine end mill is aimed at that failure: it keeps the cut clean on plywood and density board so you spend less time sanding.

This is an alloy end mill with a coated fine cutting edge, made for milling on a woodworking CNC machine. Diameter spans D6 to D22 and total length spans 90 to 120mm. The SKU in the pictures is 10X50X10X100. To confirm fit, match that size against the collet and the depth of cut your job needs before you order.

Check the shank against your collet and the flute length against your cut depth. A 3-flute spiral geometry pulls chips out of the kerf as it cuts, which is why discharge stays easy and noise stays low. Seat it, torque the collet nut, and the fine edge holds the surface finish on multi-layer board and plywood.

Packing and customisation are not stated, so ask. Send the board type, the diameter you need between D6 and D22, the total length you need between 90 and 120mm, and your CNC machine model. That lets the supplier confirm the SKU 10X50X10X100 or match another size before you commit.

What the specification fixes, and what it leaves to the machine:

• Chip clearance on plywood — 3 flutes spiral geometry lifts chips out of the cut, so discharge stays easy when milling plywood and multi-layer board on a woodworking CNC machine.
• Surface finish on density board — A coated fine cutting edge leaves a high finish of processing surface on density board, which cuts the sanding time after milling.
• Fit check at the collet — Diameter runs D6 to D22, so match the shank to your collet before ordering and confirm the SKU 10X50X10X100 against your spindle.
• Depth of cut planning — Total length runs 90 to 120mm; check the flute length against the depth you cut in multi-layer board so the shank clears the work.
• Wear point at the cutting edge — Alloy material with a coating on the fine edge is the wear point; keep the feed steady and the edge keeps its finish on plywood.
• Noise at the spindle — Low processing noise is a stated advantage of this 3-flute spiral end mill, which matters on long runs cutting density board.
• Speed on multi-layer board — Fast processing speed is a stated advantage, so a 3-flute spiral end mill keeps up with production runs on multi-layer board.

What changes on the shop floor when the right part goes back in:

• Cleaner faces off the machine. A high finish of processing surface means less sanding after milling multi-layer board and plywood, so parts move to assembly with fewer rework passes.
• Chips leave the cut. Easy discharge keeps the flutes clear on density board, which holds the cut stable through a run instead of stalling when chips pack.
• Faster through the board. Fast processing speed is a stated advantage, so a batch of plywood panels takes fewer passes at the spindle and the run finishes sooner.
• Quieter on long runs. Low processing noise is a stated advantage of this 3-flute spiral end mill, which takes the edge off a full shift cutting density board.
• Edge holds its shape. The coating on the fine alloy edge is there to keep the cutting edge working on multi-layer board, so the finish stays consistent across the batch.
• Sizes to match the job. Diameter runs D6 to D22 and total length runs 90 to 120mm, so you can pick the size that fits the collet and the depth of cut you run.
• One tool for panel work. It suits multi-layer board, plywood and density board, so one end mill family covers the panel jobs on a woodworking CNC machine.

Check the shank diameter against your collet before ordering. Diameter runs D6 to D22 and total length runs 90 to 120mm, and the SKU in the pictures is 10X50X10X100, so match that size to your spindle and the depth of cut you need.

It is made for multi-layer board, plywood and density board. The fine coated edge and 3-flute spiral geometry are aimed at those panel materials on a woodworking CNC machine, not at solid hardwood or metal.

Three flutes give the chip clearance and finish this cutter is built for on panel work. The spiral geometry supports easy discharge and fast processing speed, which is what you want when milling plywood and density board.

The coating sits on the fine alloy edge and is part of what gives the high finish of processing surface. Keep a steady feed so the edge keeps cutting cleanly on multi-layer board instead of rubbing.

Seat the shank fully in the collet and torque the collet nut before the first cut. It is a milling tool for a woodworking CNC machine, so check the flute length against your depth of cut before you run it.

Diameter runs D6 to D22 and total length runs 90 to 120mm. The SKU 10X50X10X100 shown in the pictures is one size; send your required diameter and length when you enquire so the right size is confirmed.

Low processing noise is a stated advantage of this 3-flute spiral end mill. The spiral geometry and easy discharge support smoother cutting, which helps on long runs of density board.

Send the board type, the diameter you need between D6 and D22, the total length you need between 90 and 120mm, and your CNC machine model. Packing and customisation are not stated, so ask about those in the same message.