Fine End Mill 3 Flutes High Performance Carbide Milling Cutter for Multi layer Board Plywood Density Board

A 3 flute carbide end mill for woodworking CNC machines, built to mill multi-layer board, plywood and density board. Alloy cutting edges leave a high finish on the processed surface while running at fast processing speed with low processing noise. Diameters run from D6 to D22, total lengths from 90 to 120mm. The SKU shown, 10X50X10X100, matches the pictures. Before ordering, check your collet size against the diameter you need and confirm the shank and cutting length fit your machine and job.

Edge tear-out and slow feed rates on panel work usually trace back to the cutter in the spindle. A 3 flute end mill changes how the chip leaves the cut, and that changes what the operator sees at the edge of a multi-layer board or plywood sheet.

Cut from alloy carbide, this end mill is a milling tool for woodworking CNC machines. Diameters run from D6 to D22 and total lengths from 90 to 120mm, so a buyer picks a size from the range rather than a single fixed number. The SKU in the pictures is 10X50X10X100.

Three flutes do two jobs: they carry the chip out and they keep more cutting edge in the material. Easy discharge is the point of that geometry, because a clogged flute turns into heat and a burnt edge on density board. Check the shank seats fully in the collet before the first cut and the tool spins true.

Supply runs from China, and the range covers D6 to D22 with total lengths of 90 to 120mm. Send the diameter, total length and the board type you cut with your enquiry, plus a photo or the SKU 10X50X10X100 if you are matching an existing tool. That gets you the right cutter rather than a near miss.

What the specification fixes, and what it leaves to the machine:

• Chip clearance on plywood — Three flutes give the chip a short path out of the cut, which keeps plywood and multi-layer board from packing the flutes under load.
• Surface finish on density board — A fine cutting edge leaves a high finish on the processed surface, so density board comes off the table with less edge work behind it.
• Diameter range for job matching — Cutters run from D6 to D22, letting a shop cover a narrow groove and a wider clearing pass from one tool family.
• Length selection — Total lengths run from 90 to 120mm, so deep panel cuts and shallow trim work are covered without changing the machine setup.
• Noise at the spindle — Low processing noise is one of the stated advantages, which matters on a CNC cell where operators stand at the machine all shift.
• Feed rate on panel stacks — Fast processing speed suits shops pushing multi-layer board and plywood through the machine on a fixed cycle time.
• Collet fit check — Before mounting, measure the cutter shank against your collet bore; the diameter range is D6 to D22, so confirm the exact size you order.

What changes on the shop floor when the right part goes back in:

• Cleaner edge off the table. A high finish on the processed surface means less sanding and secondary work after the cut, which shortens the route from panel to assembly on multi-layer board and plywood.
• Shorter cycle times. Fast processing speed keeps the machine moving through the board instead of easing off to protect the edge, so the same shift covers more panel work.
• Fewer stops to clear chips. Easy discharge moves the chip out of the flute, cutting the downtime spent clearing a packed cutter and the burnt edges that come with it.
• Less noise at the machine. Low processing noise is a stated advantage of the design, which makes a long panel run easier on the operator standing at the spindle.
• One family covers the range. With diameters from D6 to D22, a shop can stock one tool family for narrow and wide cuts instead of chasing separate cutters for each job.
• Lengths for deep and shallow work. Total lengths from 90 to 120mm let you pick a cutter that reaches the depth your panel job needs without a change in machine setup.

Check the shank diameter against your collet bore before ordering. These are milling tools for woodworking CNC machines with diameters from D6 to D22, so the size you pick has to match the collet you hold it in.

It is built for multi-layer board, plywood and density board. Those are the stated materials, so treat softer or harder stock as a separate question to raise with the supplier before you buy.

Three. The 3 flute geometry is the reason for the easy discharge and the finish on the processed surface, because the chip leaves the cut quickly instead of sitting in the flute.

Diameters run from D6 to D22 and total lengths from 90 to 120mm. Pick the diameter and length your job needs; the SKU 10X50X10X100 in the pictures is one point in that range.

The cutting material is alloy. That is the material stated for this cutter, and it is what carries the edge through plywood, multi-layer board and density board.

A packed flute is the usual cause, and easy discharge is what this cutter is designed for. Check the chip is leaving the cut freely and that the feed rate is not stalling the cutter in the board.

Yes, the range covers D6 to D22. Send the exact diameter and total length you need with your enquiry so the cutter matches your job rather than the nearest stock size.

Send the diameter, total length, the board type you cut and your machine spindle size. Add the SKU 10X50X10X100 or a photo if you are matching a cutter already in use.