Double Edged Compound Milling Cutter For Single Veneer Panel Double Veneer Panel Particle Board Plywood Wood

A double-edged compound milling cutter for woodworking machines, built to cut single veneer, double veneer, particle board, density board, multi-layer board and plywood. The alloy body and composite groove multi-cutting edge give a sharp cut with no raw edge. Shank diameter and blade diameter run D3.175~D10, total length 38~75mm. Check your spindle collet and required cutting diameter against those ranges before ordering; SKU 8X35X8X75 identifies this size.

Tear-out and fuzz on veneered panels usually trace back to a single-edge cutter that pushes fibres instead of shearing them. When the top or bottom face burrs, the panel needs sanding or becomes scrap. This cutter addresses that cut on single veneer, double veneer, particle board, density board, multi-layer board and plywood.

It is a double-edged compound milling cutter made of alloy, with a composite groove multi-cutting edge. Shank diameter and blade diameter both span D3.175~D10; total length runs 38~75mm. It mounts in woodworking machine tool spindles. Confirm fit by matching your collet to the shank diameter and your maximum cut depth to the blade diameter and total length.

Mount it in the collet, set the cutting depth against the panel, and check that both edges engage the composite groove cut. The double-edge layout shares the cut across two edges, which is what keeps burrs off the top and bottom faces and prevents edge explosion on veneered board.

Supply follows the size range above: shank D3.175~D10, blade D3.175~D10, total length 38~75mm, SKU 8X35X8X75. Send your shank diameter, blade diameter, total length, panel type and machine spindle speed with the enquiry so the cutter is matched to your setup.

What the specification fixes, and what it leaves to the machine:

• Veneer face cut — Cuts single veneer panel and double veneer panel without leaving a raw edge on either face.
• Particle board run — Composite groove multi-cutting edge shears particle board cleanly instead of pulling chips out of the core.
• Density board work — Sharp alloy edge takes density board cuts with no fuzz on the top or bottom surface.
• Plywood stack — Double-edged layout handles plywood and multi-layer board where cross-grain tear-out is common.
• Shank fit check — Shank diameter D3.175~D10 lets you match the cutter to your collet before ordering.
• Blade size range — Blade diameter D3.175~D10 covers small trim cuts through to wider grooving passes.
• Length selection — Total length 38~75mm gives options for short-reach and deeper-reach machine setups.
• Edge condition — No burrs above and below and no edge explosion means less sanding after the cut.
• Finish result — High finish off the cutter reduces secondary finishing time on veneered and laminated panels.
• Alloy body — Alloy construction holds the double-edge geometry through repeated panel cutting cycles.
• Material — alloy, specified for this position on woodworking machines.
• Fit — built for woodworking machines, in the position the original part occupied.
• Specified characteristic — sharp.

What changes on the shop floor when the right part goes back in:

• Less sanding after the cut. No fuzz, no burrs above and below, and no edge explosion mean panels come off the machine closer to finished, cutting hand-sanding time on veneered faces.
• One cutter covers several boards. The same double-edged compound milling cutter runs single veneer, double veneer, particle board, density board, multi-layer board and plywood, so you stock fewer tools.
• Clean top and bottom faces. Because burrs are controlled above and below, stacked or double-sided veneer panels do not need one face reworked after machining.
• Sharper cut on dense board. The sharp alloy edge and composite groove multi-cutting edge shear density board and particle board rather than compressing the surface.
• Fit confirmed before you buy. With shank D3.175~D10, blade D3.175~D10 and total length 38~75mm, you can check collet and depth against the numbers first.
• Fewer rejected veneer panels. No raw edge and no edge explosion on veneered board reduces scrap at the cut and keeps panel yield up on the run.
• Predictable finish across the batch. High finish and controlled burrs mean the cut quality holds from the first panel to the last in a production run.

Check the shank diameter against your collet; shank diameter spans D3.175~D10. Measure your collet bore and pick the cutter size inside that range before ordering.

Both run D3.175~D10, but they set different things. Shank diameter must match your collet; blade diameter sets the cut width. Confirm both against your machine.

Yes. The cutter is suitable for plywood, particle board, density board, multi-layer board, single veneer and double veneer panel.

The double-edge compound groove layout is built for this: no burrs above and below and no edge explosion. Set cutting depth so both edges engage the panel.

Total length options run 38~75mm. Pick based on your reach and cutting depth, then quote SKU 8X35X8X75 as the reference size.

The alloy edge is sharp and the composite groove multi-cutting edge is made for dense panel. It is listed for density board alongside the other panel types.

Alloy. The body and edge are alloy, which holds the double-edge geometry through panel cutting.

Send shank diameter, blade diameter, total length, panel type and your machine spindle details. That lets the cutter be matched to your setup without guesswork.