2KG PUR EVA Glue Dispensing Machine for Edge Banders Woodworking Edgebanding Machine Units

Need to run both PUR and EVA glue on one edge bander without scraping the glue roller at every change? The XE-200 is a 2 kg barrel glue dispensing unit that mounts on a standard woodworking edge banding machine. It holds three separately controlled heating zones — glue tray, glue hose, glue pot — reaches working temperature in 10–15 minutes, runs on 4 kg working air pressure, and recovers its own residual glue after a set batch. No pot disassembly, no roller scraping, and no second machine for the other adhesive.

A glue station on an edge bander fails in three ways, and all three cost shift time. The glue roller has to be scraped by hand before every glue change. Tray, hose and pot drift to different temperatures, so the band lifts at the panel end. And the change itself becomes a purge, a pressure plate that will not lift and an overflowing barrel.

The XE-200 is a 2 kg barrel glue dispensing unit built for woodworking edge banding machines. It runs PUR hot melt and EVA hot melt from the same barrel position, keeps separate temperature values for each adhesive, and carries its own self-cleaning glue pot, so the roller is no longer the cleaning point.

Heat is regulated in three independent zones. On EVA the glue tray is set to ≈200°C, the glue hose to ≈180°C and the glue pot to ≈160°C; on PUR the pot runs at ≈140°C with the EVA heating switch turned off. The green indicator reports ready after 10–15 minutes; the melt then needs 10 minutes at temperature before the first panel.

Every function sits on one full-colour touchscreen: preheating, glue removal, zone temperatures and fault prompts, with the parameter page password-locked. It bolts on through a fixed bracket and a U-shaped adapter plate, three adjustable screws set pot height, and a limit switch is already fitted. Made in China, customisation supported.

Each point below is a number you can check:

• Dual adhesive, one barrel position — PUR hot melt and EVA hot melt run from the same 2 kg barrel, and the screen keeps a separate temperature set for each, so a job change is a menu selection.
• Self-cleaning glue pot — the glue-removal routine runs from the parameter page against a batch count: 1–2 panels on thin board, 3 on multi-layer, with an adjustable delay.
• Three heating zones — glue tray, glue hose and glue pot are set apart: ≈200°C / ≈180°C / ≈160°C on EVA, ≈140°C on PUR with the EVA switch off.
• 10–15 minute preheat — ready shows as a green indicator, then 10 more minutes at temperature so the melt evens out before the first board.
• 4 kg working air pressure — the barrel lift, pressure plate and glue-removal valve run on 4 kg supply, with the solenoid hose taken off the main air pipe.
• Barrel change on screen — lift the plate, open the exhaust valve to balance barrel pressure, raise and swap the 2 kg barrel, grease the seal, lock, close.
• Separated, labelled wiring — temperature-control wires and heating wires run apart with fixed labels; the pot takes the bander's heating control through aviation-plug terminals.
• Adjustable mounting — fixed bracket plus U-shaped adapter plate, three height screws, movable guide plate and pre-installed limit switch.

The usual choice is between scraping rollers between shifts and sending panels out. This unit takes both options off the table:

• The roller stops eating the shift. Glue recovery runs after the set batch — 1–2 panels on thin board, 3 on multi-layer — so nobody stands at the pot with a scraper between orders.
• A glue change stays inside the shift. Plate lift, exhaust valve and barrel swap follow one on-screen sequence, and the 2 kg barrel goes back in without a fitter.
• One unit covers two adhesives. PUR and EVA run from the 2 kg position with their own stored temperatures, so a mixed order book needs no second glue station.
• Temperature is set per zone. ≈200 / ≈180 / ≈160°C on EVA and ≈140°C on PUR keep the hose from being cooked just to hold the tray hot.
• It goes onto the bander you already run. The U-shaped adapter plate, three height screws and fitted limit switch cover mainstream banders.
• Training fits in a QR code. Bilingual wiring labels and the video guide cover the 10–15 minute preheat, the glue change and the adhesive switch.
• Fewer consumables on the shelf. Only barrels, sealing rings and the yellow grease are replaced; the pot cleans itself and the roller is never taken apart.

Yes. Both adhesives run from the same 2 kg barrel position, each with its own stored temperature set. EVA to PUR: exhaust the leftover EVA, remove the glue hose, empty all residual adhesive, fit the PUR barrel and select the PUR parameters. PUR to EVA: consume the remaining PUR first, then enable the EVA heating switch and set the EVA values.

10–15 minutes from cold to the green ready indicator. Add a 10 minute stabilisation period at temperature before the first panel, because the melt needs to even out across tray, hose and pot first.

EVA: glue tray ≈200°C, glue hose ≈180°C, glue pot ≈160°C. PUR: glue pot ≈140°C with the EVA heating switch turned off. The three zones are adjusted separately on the touchscreen, so one zone does not force the others.

No. The self-cleaning glue pot recovers residual glue automatically after the batch count you enter — 1–2 panels on thin board, 3 on multi-layer — with an adjustable delay. Run it per batch and PUR rollers stay clean for up to 48 hours of continuous use; EVA rollers need no routine disassembly.

A 2 kg barrel, changed entirely from the screen. Lift the plate slightly, open the exhaust valve to balance barrel pressure, raise the plate, take the empty barrel out, grease the sealing ring with high-temperature yellow grease, fit the new barrel, lower and lock the plate, then close the valve.

4 kg working air pressure. The solenoid valve air hose must come off the main air pipe, otherwise the barrel lift and the pressure plate will not reach their travel and glue can leak.

Yes for standard woodworking edge banding machines, through the fixed bracket and U-shaped adapter plate with three height screws; the limit switch is already fitted. If your interface differs, customisation is supported — send the mounting layout of your machine.

One session is normally enough. The touchscreen walks through preheat, glue removal, glue change and adhesive switch step by step, the wiring labels and interface are English and Chinese, and the unit ships with a QR code to the video guide.