Edgebanding Buffing Wheels With Steel Core For Woodworking Edgebander

Changing a spent buffing wheel on an edgebanding machine should take a minute, not a shift. The BW016 is a 200 mm cotton cloth buffing wheel with a 19 mm centre hole and a 20 mm face, built on a steel core so the bore stays round on the spindle. It burnishes the trimmed edge on woodworking edge banders. Round bore is standard and hexagon is available. Wheels ship in a carton box; other sizes are quoted on request.

Every polishing station on an edge bander fails in the same three ways. The cloth glazes over and smears the glue line instead of burnishing it. The bore wears oval, the wheel runs off centre and leaves chatter along the edge. And the spare is not on the shelf, so the line waits for a courier. The BW016 steel core buffing wheel is built for that station.

It is a 200 mm outside diameter buffing wheel, 19 mm centre hole and 20 mm of face width, cotton cloth over a metal core, listed as a polishing wheel for woodworking edge banding machines. The 200 mm diameter sets the contact circle; the 20 mm face spans the trimmed edge in one pass.

The steel core is the real difference. Cloth alone lets the bore creep out of round as the wheel heats and loads, and an oval bore turns a smooth polish into vibration. A metal core holds the 19 mm hole true on the shaft for the whole life of the face. Round bore is standard; a hexagon bore suits machines that drive the wheel on a hex spindle.

Fitting is a slide-on job: lift the spent wheel off the 19 mm shaft, seat the new one, re-tension. Wheels travel in a carton box, and other diameters, thicknesses and bore shapes can be quoted on one order.

Each number below is a fit dimension or a build detail — measure the spindle and the wheel pocket before ordering.

• 200 mm outside diameter — the working circle that decides how much edge the cloth reaches per pass.
• 19 mm centre hole — the bore that decides fit; a 19 mm shaft takes this wheel directly.
• 20 mm face width — wide enough to span the trimmed edge in one pass instead of a thin band.
• Steel core — holds the 19 mm bore round under heat and load, so the wheel stays concentric.
• Cotton cloth face — burnishes rather than cuts, so the trimmed PVC or veneer edge comes out glossy.
• Round bore as standard — a hexagon bore is available for machines driven on a hex spindle.
• Edge bander fitment — listed as a polishing wheel for woodworking edge banding machines.
• Slide-on replacement — no adapter bush and no shimming; the wheel seats on the shaft by hand.
• Visible wear — the face flattens and stops holding compound, so replacement is decided by looking.
• Carton box packing — each wheel arrives flat and protected, ready to hang on the shelf.
• Other sizes on request — 200×19×20 mm is this listing; other diameters, thicknesses and bore shapes quote fast.

A shop with a dull polish station has two choices: wait on the machine builder's parts desk, or fit whatever wheel is nearest to hand. This is the third.

• A fit you can check before you buy. Bore, diameter and face are published — 19 mm, 200 mm, 20 mm. Measure the shaft and the pocket, and the fit is settled before the order leaves.
• No adapter, no shimming. The 19 mm bore is sized for edge bander polish spindles, so the wheel seats on the shaft that is already on the machine.
• The gloss holds through a shift. A steel core keeps the wheel concentric, so pressure along the glue line stays even.
• Less scrap from a spent wheel. Cotton glazes to a shine when it is done, so operators swap on sight instead of after a batch of panels has run.
• Replacement without stripping the station. The spent wheel lifts off the 19 mm shaft and the new one slides on, so the line is back in the run in minutes.
• One order covers a mixed machine park. Other diameters, thicknesses and bore shapes — round or hexagon — are quoted on request, so a second bander is covered by the same shipment.
• Cheap to stock. A light consumable in a carton box, it rides along with heavier spare parts and pays no extra freight.

Check three numbers: 200 mm outside diameter, 19 mm bore, 20 mm face. If they match the wheel you are replacing, it fits directly. If the shaft or the pocket differs, the same wheel can be quoted in the size you need.

It keeps the 19 mm bore round on the spindle. Cloth alone deforms as it heats and loads, and an oval bore makes the wheel run off centre, which shows up as chatter along the glue line.

Cotton. Cotton burnishes and brings up gloss, while sisal cuts harder and leaves a coarser surface. For the polish station after edge trimming, cotton is the medium that matches the job.

Yes. Round is the standard for this listing, and a hexagon centre hole is also available. Tell us which shaft the machine uses and the wheel will be quoted to match.

Yes. 200×19×20 mm is what this listing covers; other diameters, thicknesses and bore shapes are available on request. Send the size of the wheel you are replacing and the equivalent can be quoted.

In a carton box. Each wheel is a light consumable, so it packs flat and can travel together with heavier spare parts on the same order.

When the face flattens or glazes, not on a fixed calendar. Wear follows the metres of edge banding you run and the compound you use, so two shops on the same wheel will not replace it on the same schedule.

Three numbers: outer diameter, bore and thickness — 200 mm, 19 mm, 20 mm on this wheel. Add the machine make and model, and the fit can be confirmed without sending a sample back and forth.