VCBL-K2-120X50X50 Q Vacuum Block for Homag CNC Machine Vacuum Suction Cup

Replacing a worn pod on a Homag table? The VCBL-K2-120X50X50 Q is the spare that carries that mode: 120 × 50 mm in plan, 50 mm high, suction face arranged crossways, part number 10.01.12.00772. Body in rubber and plastic, sold as one block, and the suction plate for the vacuum block is listed as a separate spare. All three dimensions are published, so the old block can be measured with a rule before the order goes out. Price on request, quoted against the quantity you need.

Three things go wrong at a Homag clamping table, and none reads as a machine fault. A pod stops sealing, so the panel lifts under the cutter. Blocks from an earlier job get mixed in, so the 120 × 50 mm faces no longer sit in one plane. A rubber face wears through mid-shift. All three come back as scrap. The VCBL-K2-120X50X50 Q is the spare that answers them.

It is a vacuum block — a suction pod that pulls the workpiece down onto the machine table. Plan size 120 × 50 mm, height 50 mm, suction face arranged crossways. Mode VCBL-K2 120x50x50 Q, part number 10.01.12.00772. Those three dimensions are published, so they can be measured against the block you are removing before the order goes out.

Construction is listed in two materials, rubber and plastic. The plastic body holds the 120 × 50 × 50 mm envelope square and takes the clamping load; the rubber face is the part that seals against the panel.

Application is spares for CNC machines, on the Homag pods that take this mode. Servicing is two steps: check the rubber face for cuts, then fit a new suction plate or a complete block and re-check the panel for rock. Suction plates are a separate spare. Price on request.

Eight items sit on the published sheet, and each one is a figure you can check on the block you are taking off.

• 120 × 50 mm footprint — the plan size across the two sides of the seating face, printed in the mode number as 120x50.
• 50 mm height — total height H, the third figure in VCBL-K2 120x50x50 Q, so all three dimensions go on one tape measure.
• Crossways arrangement — the suction face is laid out crossways against the block body; note the orientation before the old pod comes out.
• Two materials — rubber for the sealing face, plastic for the structural body; each does one job and each is serviceable.
• Part number 10.01.12.00772 — the ordering reference, quoted separately from the mode number, so the line item is unambiguous.
• Suction plates as a separate spare — the plate is listed on its own, so a worn rubber face does not force a new block.
• Homag CNC fitment — listed as spares for CNC machines, for the Homag pods that take the VCBL-K2 120x50x50 Q block.
• Price quoted, not listed — one price per block against the spare list you actually need to change.

On a worn pod the choice is an outside repair, a pad that nearly fits, or the part specified for the machine. The cost of the wrong one is a scrapped panel.

• You order by number, not by photo. Mode VCBL-K2 120x50x50 Q and part 10.01.12.00772 both go on the order, so the block that arrives is the one you measured.
• Three dimensions checked in a minute. 120 × 50 mm footprint and 50 mm height — if the old block measures differently, you know before it ships.
• A sealing face that is a spare. Suction plates are listed separately, so the 50 mm block body stays on the machine and only the rubber goes in the bin.
• Two materials, two failure modes. A cut shows on the rubber face; a cracked body shows at the 120 × 50 mm seating edge. Both checks are done at the table.
• Crossways layout on the sheet. The arrangement is published, so a mixed set can be sorted back into one plane instead of being binned.
• Same envelope, no new fixture. Fitment is listed for Homag CNC pods that take this mode, in the 120 × 50 × 50 mm envelope.
• A quote, not a price list. Price on request means one line per block against the spare list, so you pay only for the parts you replace.

Only if the mode matches. This block carries mode VCBL-K2 120x50x50 Q and part number 10.01.12.00772; check both against the block you are removing, plus the 120 × 50 mm footprint and 50 mm height, before ordering.

120 × 50 mm in plan and 50 mm high. All three figures sit in the mode number VCBL-K2 120x50x50 Q, so the name is the specification.

Quote the suffix as written. The mode is VCBL-K2 120x50x50 Q — the Q belongs to the ordering name — and the suction face is arranged crossways, which is listed on the parameter sheet.

Yes. Suction plates for the vacuum block are listed as a separate available spare, so a worn sealing face can be replaced while the plastic body stays in place.

Rubber and plastic. The rubber is the sealing face that touches the panel; the plastic carries the 120 × 50 × 50 mm body.

One block per pod position. Count the positions on your table that currently take the VCBL-K2 120x50x50 Q mode, and order to that count — nothing on this sheet sizes a table for you.

Price is on request. Send the quantity of blocks and suction plates you need and the quote comes back against that list.

Look at the rubber face first. Cuts, flat spots and a polished shine on the 120 × 50 mm face mean the seal is no longer doing its job, and a panel that rocks on the pod confirms it.