VCBL-K2 120x50x100mm Q Vacuum Suction Cup for HOMAG Weeke CNC Machine Vacuum Cup Manufacturer

Need to keep an HOMAG or Weeke table holding panels while the old cup goes hard? The VCBL-K2 120x50x100mm Q vacuum suction cup is the direct-fit answer: 120 mm top length, 50 mm top width, 100 mm height, clamp type K2, direction Q, ordered as VCB302-B. The face is wear-resistant rubber and covers six panel types from melamine to HPL. It sits on HOMAG-series vacuum systems and compatible Weeke centres with no adapter. Customization is supported; price quoted per order.

Three things go wrong when a cup on a nesting table wears out. Vacuum drops during the cut and the panel creeps a millimetre under the tool. The spare is ordered by a code nobody can read off the old cup, so the wrong height arrives. And a whole pod is scrapped because only the sealing face was tired. This cup is aimed at all three.

It is the VCBL-K2 120x50x100mm Q vacuum suction cup, ordered as VCB302-B. The pad face measures 120 mm top length by 50 mm top width, and the body stands 100 mm tall. Clamp type is K2, direction is Q — the Q form is the airflow side of the part, a port path shaped so suction builds at the face instead of bleeding around it.

The sealing face is wear-resistant rubber, picked for the elasticity that keeps a seal through repeated clamping rather than going hard. Six panel types are listed: melamine, MDF, plywood, solid wood, HPL and composite board — one cup across the board mix a panel shop cuts in a week.

Fitment is direct on HOMAG-series vacuum systems and compatible Weeke centres, so a change is lift-off and press-on at the same grid position, no adapter plate and no re-teach. Customization is supported, origin is China, and the price is quoted per order rather than printed.

What the part is, written as numbers instead of adjectives.

• 120 x 50 mm pad face — top length 120 mm, top width 50 mm, both carried in the model code — a caliper check against the old cup settles it in a minute.
• 100 mm standing height — the body returns the table to the height it had, so pod positions need no re-teaching after the swap.
• Clamp type K2 — the K2 body form is stated for this number and ordered as K2, not guessed from a product photo.
• Q direction — the Q-form port path is the airflow side of the cup, so vacuum reaches the 120 x 50 mm face faster.
• Wear-resistant rubber face — chosen to stay elastic under repeated compression, the duty a nesting table puts on it every cycle.
• Six panel types — melamine, MDF, plywood, solid wood, HPL and composite board are all listed for this cup, so one number covers the mix.
• HOMAG and Weeke fitment — direct fit on HOMAG-series vacuum systems and compatible Weeke centres, with no adapter plate.
• VCB302-B order number — the number that goes on the request, so a 120x50x50 or a 125x75x100 cup cannot arrive in its place.
• Customization supported — a size or form that differs from 120 x 50 x 100 mm is quoted from the same request, not refused.

The usual answer to a soft cup is to wait on the machine builder's spare, or to keep running the tired one and check the cut afterwards. Neither costs less than the part.

• Vacuum comes back, not just a part number. A 120 x 50 x 100 mm cup goes back on the position it came off, so the seal is renewed without re-setting the grid.
• Order by number, not by picture. VCB302-B and VCBL-K2 120x50x100mm Q both go on the request, so the 120x50x50 height cannot arrive as a near miss.
• One height to keep. 100 mm matches the body it replaces, which is one setup step skipped at every position on the table.
• One cup for the whole board mix. Six panel types are listed, melamine through HPL, so the shelf holds one number instead of a size per material.
• A seal built to be compressed. The working surface is wear-resistant rubber, so clamping pressure is the designed duty of the part rather than the exception.
• Quoted before anything is packed. Price is by request, so size, number and quantity are confirmed in writing before the cup leaves the shelf.
• Custom work is priced, not refused. Customization is supported, so a drawing that differs from 120 x 50 x 100 mm gets a quotation instead of a no.

HOMAG and Weeke CNC machines. It is the VCBL-K2 120x50x100mm Q cup, ordered as VCB302-B, and it fits HOMAG-series vacuum systems and compatible Weeke centres, clamp type K2, direction Q.

No — the height is different. This one stands 100 mm; a 50 mm body is another item. Measure the height of the old cup first, because the footprint alone will not settle it.

Millimetres plus two form codes. 120 mm is the top length, 50 mm the top width, 100 mm the height; K2 is the clamp type and Q is the direction.

It shapes the airflow path at the face. The Q form is specified so vacuum builds quickly across the 120 x 50 mm face instead of bleeding around the port.

Melamine, MDF, plywood, solid wood, HPL and composite board — six types are listed for this cup, so the same part covers the boards a nesting shop cuts.

Yes. Customization is supported, so a size or form that differs from 120 x 50 x 100 mm is quoted from the same request.

The price is quoted per order, not fixed on the page. Send VCB302-B or VCBL-K2 120x50x100mm Q with your quantity and the quotation is returned for that quantity.

Measure it. A 120 mm by 50 mm face, a 100 mm body and a K2 clamp means this is the part; if any of the three differs, it is a different number.