140*110*50MM CNC Vacuum Cups For Anderson Giben PTP Masterwood 10011200626

Need to replace a worn vacuum cup on a nesting table without waiting on the machine builder? This is the 140 x 115 x 50 mm vacuum block, model 10011200626 (10.01.12.00626), the spare listed for Homag woodworking CNC machines and for the Schmalz 2-circuit console. Height is 50 mm, footprint 140 x 115 mm, and replacement rubber pads are available for the same block. Anderson, Giben PTP and Masterwood centres are listed under the same number. Send your machine model and the number on the old block, and the fit is confirmed before quoting.

A nesting cell that loses vacuum mid-cut scraps the panel, not just the part: the sheet shifts, the cutter digs in, and the operator spends the shift re-cutting. Most shops hit the same three things—a cup gone hard and no longer sealing, a machine builder quoting weeks for a spare, and a part number written three different ways on three documents. This vacuum cup is aimed at all three.

It is the 140 x 115 x 50 mm vacuum block / vacuum cup, sold as 10011200626 and 10.01.12.00626. The block is a replacement spare for Homag woodworking CNC machines and the Schmalz 2-circuit console, and the same number is listed for Anderson, Giben PTP and Masterwood processing centres. At 50 mm height it sits at the same Z reference as the block it replaces, so the table setup does not need re-teaching.

Rubber pads for this block are available on their own, which matters because the pad is the part that wears: renew the sealing face and the block goes back to work, without retiring a 140 x 115 mm body because the seal went flat. Pads and other vacuum cups are quoted together with the block.

This is a spare part ordered by number: give the machine model, the old block number and the quantity, and the match is checked before packing. No drawing is needed.

What you actually get in the box, stated as numbers rather than adjectives.

• Exact 140 x 115 x 50 mm envelope — the block matches the footprint and the 50 mm working height of the original, so the panel sits on the same Z reference after the swap.
• Two numbers, one part — order it as 10011200626 or as 10.01.12.00626; both formats appear on machine builder parts lists for this block.
• Homag CNC fitment — listed as a spare for Homag woodworking CNC machines, the machines these pods are normally pulled from when a seal fails.
• Four machine families — the same number is listed for Anderson, Giben PTP and Masterwood processing centres, so a mixed machine shop stocks one line instead of four.
• Schmalz 2-circuit console — named for the Schmalz 2-circuit console, so it is ordered as a console block rather than guessed from a photo.
• Replaceable rubber pads — pads are available separately for this block, which turns a 50 mm block replacement into a pad change.
• Spare-part box, not a machine — one block is one item: no fixture, no plumbing kit and no control hardware to budget for.
• Other accessories on request — pads, other vacuum cups and further CNC machine spare parts are quoted from the same number, with no extra sourcing step.

The usual choice on a worn cup is to wait for the machine builder's spare and lose table time, or to shim the old block and hope the seal holds until the next service. Neither is cheaper than the part.

• One number covers four machine families. Anderson, Giben PTP, Masterwood and Homag machines all reference 10011200626, so four machines on one shop floor share one spare line.
• The seal is the only wearing surface. Renew the pad and the 140 x 115 x 50 mm body keeps working, so the block is bought once and refreshed rather than replaced whole.
• Same height, no re-setup. At 50 mm the block returns the table to the same reference, which saves re-teaching pod positions after a swap.
• No drawing, no guessing. The number is printed on the old block: quote 10011200626 and the match is confirmed before packing, so the wrong pod never becomes a return.
• Sized for a caliper check. 140 x 115 x 50 mm can be measured on the bench in under a minute, so a buyer can verify the fit before ordering rather than after.

Yes, if the number on the old block reads 10011200626 or 10.01.12.00626. The block is listed as a spare for Homag woodworking CNC machines and for the Schmalz 2-circuit console, at 140 x 115 x 50 mm.

It is 140 x 115 x 50 mm: a 140 mm x 115 mm footprint with a 50 mm height. Measure the old block across its widest face and then at the seal; if both readings match, this is the part.

Just the pad, as long as the block body is still flat and uncracked. Rubber pads for this block are available separately, and changing the pad is the cheaper way to restore a seal.

Match the number rather than the picture. The block is listed under 10011200626 for Anderson, Giben PTP and Masterwood processing centres, and the 140 x 115 x 50 mm size is the second check you can make with a caliper.

One per table set, plus one spare. A single hardened cup can stop a whole nesting shift, so the spare quantity should cover every pod position that runs daily.

It is quoted, not fixed-price. Send the number 10011200626 and the quantity you need, and the quote is returned for that quantity.

Yes. Other accessories are available on request, including pads for this block and other CNC vacuum cups and machine spare parts. Send the numbers and they are quoted together.

Individually wrapped, then cartoned and labelled with the product name and quantity. Each block is wrapped on its own before packing, so the sealing face does not rub against another block in transit.