10.01.12.02325 Vacuum Suction Cover 140*130*17mm Upper Rubber Pad for CNC Woodworking Machine

Need to replace a vacuum cup top on a HOMAG drilling centre? The 10.01.12.02325 cover is the upper rubber pad you drop in: 140 mm long, 130 mm wide, 17 mm thick, molded in grey rubber, catalogued as VCB414. It fits HOMAG CNC drilling machines and HOMAG CNC router processing centres that use this cup footprint, and it is the wear half of the cup, so you replace the pad instead of the whole assembly. Check the three dimensions against your old pad before ordering, and pack spares in the carton they arrive in.

A shop running HOMAG drilling centres usually meets the same three problems: a cup that stops holding vacuum once its rubber top has flattened, a machine sitting idle while a replacement part is sourced, and a cover ordered by eye that arrives with the wrong footprint.

The 10.01.12.02325 vacuum suction cover is the upper rubber pad that closes all three. It measures 140 mm long, 130 mm wide and 17 mm thick, is molded in grey rubber, and carries the upper suction plate in the same body, so there is no bonded plate to peel off under vacuum.

It is listed for HOMAG CNC drilling machines and HOMAG CNC router processing centres, and it suits any CNC machine that uses the same cup footprint. The panel rests on this pad, not on the cup body, so this is the part that takes the load and the wear.

Catalogue code VCB414, part number 10.01.12.02325. Because a cover is a wear item, ordering by part number and by three dimensions is faster and safer than measuring a flattened original on the table. Each cover is packed in a carton, so a service stock arrives flat and undistorted, and a fitter can swap one during a shift break instead of booking a service visit.

What makes this cover a wear part rather than a rubber offcut:

• Upper suction plate molded in. The sealing face and the pad are one rubber body, so nothing is glued on to lift at the edges.
• 140 x 130 x 17 mm, to the millimeter. All three fit dimensions are stated, so a caliper check against the old pad settles it before you order.
• Grey rubber body. Molded rubber, not foam and not PVC, so the face returns to shape after each clamp and keeps its 17 mm profile.
• Made for HOMAG drilling centres. The cover is listed against 10.01.12.02325 for HOMAG CNC drilling machines and HOMAG CNC router processing centres.
• Upper cover only. This is the top pad alone; the lower suction plate is a separate part number.
• Low 17 mm profile. A 17 mm pad keeps the panel close to the cup body, so clamping height across the table stays even without shimming.
• Lifts off, presses on. It seats on the cup body, so a change is a lift-and-press job on the machine.
• Carton packing. Each cover ships in a carton, so a batch of spares arrives undistorted and goes straight onto the spares shelf.
• One code to reorder. VCB414 and 10.01.12.02325 both point at the same 140 x 130 x 17 mm pad.

On a vacuum cup the usual choice is between a cheap pad that flattens in weeks and a full cup assembly that costs many times more. This cover is the middle path:

• Replace the wear part, not the cup. The rubber top wears first and the cup body does not, so buying the 140 x 130 x 17 mm cover alone keeps a spare on the shelf for the price of one component.
• Fewer panels lost to a bad seal. A flat, uncut face seals across its whole area, so the panel stays down through the drilling cycle instead of creeping on the last holes.
• Order by number, not by memory. 10.01.12.02325 and VCB414 both resolve to one dimension set, so the next order is the same part and not a lookalike from another supplier.
• Downtime counted in minutes. The cover comes off and goes back on the cup body by hand, so no re-alignment of the machine table is needed to get back into production.
• A spares shelf that stays usable. Carton packing holds pads flat until they are needed, so stock bought in advance does not quietly flatten and turn into scrap.
• Even clamping across the bed. Every cover is 17 mm thick, so cups set at the same height hold the panel level instead of tilting it over one short pad.

Yes, if your cup takes the 10.01.12.02325 cover. The cover is listed for HOMAG CNC drilling machines and HOMAG CNC router processing centres, and it seats on the cup body rather than on the machine frame, so the cup footprint decides fit, not the machine age.

Yes. 10.01.12.02325 is the part number on the machine side and VCB414 is the catalogue code for the same 140 x 130 x 17 mm grey rubber upper cover. Both codes can be used to reorder.

Three dimensions: 140 mm long, 130 mm wide, 17 mm thick. Lay the old cover flat and measure across the longest side first, then across the shorter side, then through the thickness at the centre, where wear is lowest.

Only the upper cover. The item is the upper rubber suction cover itself; the lower suction plate and the cup body are separate parts, which is why this cover can be replaced on its own.

Grey molded rubber. The body is molded in one piece with the upper suction plate in it, so the sealing face and the pad are the same material instead of two parts bonded together.

Replace it when it stops sealing, not on a fixed schedule. A face that has flattened, hardened or been cut by panel edges leaks air at the contact line, and that shows up first as panels creeping during drilling, not as a visible tear.

Packed in a carton, and priced per order on request. The cover ships in a carton so a batch of pads arrives flat, and the price is quoted against the quantity you send, since quantity changes the price per piece.

Yes. The cover is listed for HOMAG CNC router processing centres as well as HOMAG CNC drilling machines, so it works on any CNC machine that uses a cup of this 140 x 130 x 17 mm footprint.