160*115*17mm Vacuum Suction Plate Lower Rubber Pad For CNC Woodworking Machine

Need to renew the stepped lower rubber plate under a vacuum cup on a HOMAG drilling centre? VCB413 is that plate in step version: 160 x 115 x 17 mm, grey rubber, with a moulded step in the 17 mm section. Length 160 mm, width 115 mm, section 17 mm — measure the worn pad, then check the step, and the fit is settled. It is the lower plate the cup sits on, not the top cover that meets the panel. Carton packed, price on request.

A vacuum cup rarely loses grip at the pump; it loses it at the rubber plate under the cup. The lower pad goes hard, the panel creeps a fraction of a millimetre between drilling cycles, and the spare that finally arrives is the flat plate when the cup on the table takes the stepped one.

VCB413 is that stepped plate: the lower rubber suction plate for CNC vacuum cups in step version, 160 x 115 x 17 mm, moulded in grey rubber and listed for use on HOMAG CNC drilling machines. It is the lower plate the cup sits on, not the top cover that meets the panel.

Step version is what separates it from the flat plate. The 17 mm section carries a moulded step, so the replacement has to match the cup recess on the table, not just the footprint. 160 mm long, 115 mm wide and 17 mm thick are the three figures a rule across the worn pad settles; the step is the fourth check.

Fitting is a pad swap: the plate lifts out and the cup keeps its position, so the job restarts on the same datum. Packed in a carton as a spare, made in China, price on request.

What the 160 x 115 x 17 mm stepped plate gives you at the cup:

• 160 x 115 x 17 mm face — length, width and section are the whole fit check, settled by a rule across the old pad.
• Step version — the 17 mm section carries a moulded step instead of a flat face, for cups that take the stepped lower plate.
• Grey rubber, one moulding — a single pad with 17 mm of section, so the cup returns to its original height when the plate goes back in.
• Lower plate position — this is the plate under the cup; the top cover that meets the panel is a separate item.
• Listed for HOMAG CNC drilling machines — the machine family named in the product data; check the cup recess before ordering.
• Part number VCB413 — quote it with 160 x 115 x 17 mm and the order needs no photograph.
• Top cover 4-011-11-0196 available — the upper rubber cover named alongside this pad can travel in the same order.
• Flat partner plate — the same 160 x 115 x 17 mm envelope is offered without a step, so a table with both cup types is one delivery.
• Carton packed — sealed as a spare and travels with other vacuum cup spares.
• Price on request — quantity plus the three measurements gets a quote checked against stock.

When the lower pad gives up there are two bad options — keep running and chase the panel, or pull the cup and lose the setting. This is the third:

• A pad change, not a cup change. The 17 mm base lifts out and the cup keeps its position on the table, so the job restarts on the same datum instead of a re-set one.
• Step matched, not filed down. The plate arrives with the step moulded in, so there is no shoulder to cut and no packing to make before it goes in.
• Four facts settle the order. 160 mm, 115 mm, 17 mm and VCB413 — the same four that keep the wrong pad out of the parcel let a stores clerk order without help.
• Base and cover in one delivery. The top cover named alongside this pad, 4-011-11-0196, can ship with the plates, so a cup is renewed in one shipment rather than three.
• Both versions, one order. The stepped plate and its flat partner share the 160 x 115 x 17 mm envelope, so two cup types on one table do not become two shipments.
• Renew the rubber, keep the hardware. Only the plate is consumed; the pod body, its height setting and the top cover stay, so 17 mm of rubber is the whole spend.

Yes, if the cup takes a stepped lower plate and the old pad measures 160 x 115 x 17 mm. Measure the worn plate across, along and in height, check that the face carries the step, then quote VCB413.

Step version. The 17 mm section carries a moulded step; the flat no-step plate of the same 160 x 115 x 17 mm footprint is a separate item.

The lower plate. It is the rubber the cup sits on; the top cover that meets the panel is a separate part, and 4-011-11-0196 is the one named alongside it.

No. The plate lifts out of the cup and the cup stays where it is, so the pod body, its position on the table and the top cover are untouched.

With a rule on the old pad. 160 mm long, 115 mm wide and 17 mm thick is the whole specification, and the step is the fourth check.

Rubber, in grey. It is moulded as one pad at 160 x 115 x 17 mm in the step version, so material, colour and geometry all follow from the part number.

In a carton, as a packed spare. The plate travels with other vacuum cup spares, and how it is sent is agreed when the order is placed.

Price on request. Send the quantity, VCB413 and the three measurements — 160 x 115 x 17 mm — and the quote comes back against stock.