4-011-11-0077 Rubber Vacuum Suction Plate 10.01.12.00488 For CNC Vacuum Pod

This is the upper rubber suction plate for a HOMAG CNC drilling machine, 140 × 115 × 17 mm, three holes, grey rubber, sold as a replacement top cover for the vacuum pod. It fits the pod body already on the machine, so the lower plate and the vacuum line are untouched. Three references point to the same plate: 4-011-11-0077, 4011110077 and 10.01.12.00488; VCB407 is our own stock code. Packed in a carton. Measure the worn plate, count its holes, then quote the number.

Three things go wrong on a nesting table once a suction plate is past its life. The sheet lifts at the corner on the last pass, the pod holds at low vacuum but drops when the cutter loads it, and the plate is ordered from a photograph because the number is worn off. All three start with the wrong plate arriving.

It is the upper rubber suction plate for a HOMAG CNC drilling machine, the top cover that sits on the pod and meets the board. Dimensions are 140 × 115 × 17 mm, long side 140 mm, three holes, grey rubber. It is a replacement top rubber cover, not a complete pod: the pod body, the lower plate and the vacuum connection stay on the machine while this plate is changed.

Check the size before ordering. Measure length and width on the flat, count the holes, and compare. 140 × 115 mm with three holes is this plate; a different figure is another plate in the same family, and the catalogue covers those as well.

Price is quoted on request because the plate is sold by reference. Quote 4-011-11-0077, 4011110077 or 10.01.12.00488 — the three numbers used for this item — and the quotation returns on the same line. Packed in a carton.

What the specification fixes, and what has to be checked on the machine:

• Upper plate only — the rubber top cover, so the pod body, the lower plate and the vacuum line are reused instead of replaced.
• Size — 140 × 115 × 17 mm, the one figure to compare with the worn plate before ordering.
• Long side — 140 mm, measured on the flat of the plate rather than around the edge.
• Three-hole version — the plate arrives with the three holes the pod is drilled for, so no rubber is drilled on the bench.
• Material — rubber; the contact face that meets the board is rubber, as on the part being replaced.
• Colour — grey, the finish shown on the plate in the product photographs.
• Machine fit — HOMAG CNC drilling machines, the pod family this plate is catalogued for.
• Position — top of the pod; the lower plate is a separate item in the same family, ordered under its own reference.
• References — 4-011-11-0077, 4011110077 and 10.01.12.00488 all point to this plate; VCB407 is our stock code.
• Packing — carton, the pack used for the rest of the vacuum cup range.
• Category — catalogued as a woodworking machinery spare part alongside the other pod plates.

The usual choice is between a plate that no longer seals and one ordered twice. Size and reference are on this page, so neither is a guess.

• Measure once, order once. 140 × 115 × 17 mm is on this page, so the worn plate can be checked with a rule before the order goes out.
• Three references, one plate. 4-011-11-0077, 4011110077 and 10.01.12.00488 are used for this item, so whichever number is on the maintenance sheet, the order lands on the right part.
• Only the top cover is changed. The pod body, the lower plate and the vacuum line stay on the machine, so a repair is one plate, not a pod assembly.
• Three holes, as built. The plate comes with the three holes the pod is drilled for, so the fit does not depend on somebody drilling rubber at the bench.
• Upper and lower kept apart. This listing is the top plate only, so an order for the upper cover does not come back with the lower plate that was not needed.
• Board positioning depends on it. The plate is the surface the wooden board sits on; its 140 × 115 mm footprint and three holes decide whether the board is square.
• Packed flat. Each plate is packed in a carton rather than a bag, so the contact face is not pressed against other parts in transit.

Yes, if the pod takes a 140 × 115 × 17 mm upper plate with three holes. Measure the worn plate on its flat and count the holes; if both match, the fit is confirmed before you order.

It is the top plate. The listing is the upper rubber suction plate that sits on the pod and meets the board; the lower plate is a separate item in the same family.

Three. This is the three-hole version, which is also the point to check on the worn plate, because the hole count is what separates the versions in this family.

Rubber, in grey. The contact face that reaches the board is rubber, matching the part being replaced rather than a hard cover.

Any of 4-011-11-0077, 4011110077 or 10.01.12.00488. All three are used for this plate and VCB407 is our stock code, so a quotation can be issued against whichever number your paperwork carries.

It positions wooden boards on the vacuum pod of a HOMAG CNC drilling machine. It is a replacement top rubber cover, so it goes back in the position the original plate occupied.

In a carton. Price is quoted on request, so send the part number and the quantity and the answer comes back on the same reference.

Yes. The same range covers other pod sizes and the lower plate, so send the dimensions of the part you are replacing and the nearest match is confirmed, including sizes not listed on this page.