Vacuum Suction Cup Cover Vacuum Pod Rubber Plate For CNC Machines 140*115*17mm

Need to replace a glazed top pad on a HOMAG CNC drilling machine without buying a whole vacuum pod? VCB406 is the upper rubber suction plate for the 140 x 115 x 17 mm pod: grey rubber, one-hole version, 140 mm long, 115 mm wide, 17 mm high. It is the face that meets the panel every cycle, so it wears first. Measure the old plate before ordering; the lower plate for the same footprint is a separate part. Carton packed, shipped by air, sea or express.

A vacuum pod that lets go mid-cycle usually has one worn part, not a failed machine: the top rubber plate. Three problems repeat. The pad glazes over and stops sealing with no tear. The operator buys a complete vacuum cup when only the cover was spent. Or the cover arrives in the wrong version: wrong hole pattern, or 130 mm wide instead of 115 mm.

VCB406 is the upper rubber suction plate listed for the 140 x 115 x 17 mm pod on HOMAG CNC drilling machines. It sits on top of the pod, meets the panel and keeps the workpiece from shifting under the drill and the router. It comes as the one-hole version in grey rubber: centre vacuum hole and grey contact face are both part of the replacement.

Three numbers settle the fit: length 140 mm, width 115 mm, height 17 mm. At 17 mm the new plate stands as high as the old one, so pod height and the drilling program stay untouched. A 140 x 130 x 17 mm upper cover and a lower plate for the same 140 x 115 mm pod also exist, so the order is measured, not photographed.

Carton packed; ships by air, by sea or by express. Price quoted against VCB406 and your quantity.

Nine facts decide whether this cover fits your pod.

• One-hole version — a single centre vacuum hole; one-hole and multi-hole covers are not interchangeable, so check the old plate before ordering.
• 140 x 115 x 17 mm — length 140 mm, width 115 mm, height 17 mm: the three figures that fix the fit.
• Upper plate only — this is the top rubber plate. The lower plate for the same 140 x 115 x 17 mm footprint is a separate item.
• HOMAG CNC drilling machines — the machine family this cover is listed for, on woodworking CNC pods of the same 140 x 115 mm footprint.
• Grey rubber face — moulded rubber, not a hard disc, so the contact face follows the panel surface.
• 17 mm plate height — the same standing height as the part it replaces, so pod height and program stay as they are.
• Wear shows on the face — glazing and fine crazing are visible at inspection, before a panel shifts under the spindle.
• One wear part per order — cup body, valve insert and locating ring stay in service; only the cover is swapped.
• Carton packed — plates ship flat and store as a shelf spare beside the pods.

Keep running a glazed pad and scrap panels, buy a whole vacuum pod, or swap this cover by itself. This part is the third option.

• Replace the wear part, not the assembly. The plate is what touches the panel, so one swap restores hold for the cost of a small part instead of a whole pod.
• One number, no guessing on version. VCB406 is the upper plate for the 140 x 115 x 17 mm pod; the lower plate sharing that footprint is ordered separately.
• No pod re-setting. At 17 mm high and 115 mm wide it matches the pod it is listed for, so height and program stay untouched.
• Measure once, buy once. Compare 140 mm, 115 mm and 17 mm against the old plate. A 140 x 130 x 17 mm cover will not seat on this pod.
• A consumable that lives on the shelf. At 140 x 115 x 17 mm and carton packed, a spare set sits beside the pods it fits.
• Confirmed by dimension, not by photograph. Three numbers settle the order — 140 mm, 115 mm, 17 mm — so a wrong plate is caught at the desk.

Upper. VCB406 is the upper rubber suction plate for the 140 x 115 x 17 mm pod. The lower plate for the same footprint is a separate item, so quote the position of the worn part together with the size when you enquire.

Yes, if the pod takes a 140 x 115 x 17 mm one-hole cover. Measure the old plate across length, width and height and compare against 140 mm, 115 mm and 17 mm; the outline fixes the fit, not the number stamped on the pod body.

One hole. This listing is the one-hole version, with a single centre vacuum hole. If the old plate shows a different hole pattern, it is not this cover even when the outline measures the same.

Rubber, in grey. The grey face is practical in service, because glazing and fine crazing show up before the pad stops sealing, so wear is checked by eye rather than by a panel that moved under the drill.

No. A 140 x 130 mm cover is 15 mm wider than this plate, and the width is the dimension that decides the seat. This cover is 115 mm wide and fits only the 140 x 115 x 17 mm pod.

No. The rubber plate is a separate top cover, so it comes off on its own. Cup body, valve insert and locating ring stay where they are, and a cover swap puts the pod back into service without touching the vacuum line.

HOMAG CNC drilling machines, and woodworking CNC pods of the same 140 x 115 mm footprint. It is a panel-holding part: the pod pulls vacuum and the rubber face keeps the workpiece from shifting during drilling and routing.

Carton packed, shipped by air, by sea or by express. Send the part number VCB406, the size 140 x 115 x 17 mm and the quantity, and the price is quoted against that.