4011110196 Top Vacuum Suction Plate Rubber Pad For CNC Machine 4-011-11-0196

Need to replace a worn top pad on a HOMAG CNC drilling machine without buying a whole vacuum cup? The 4-011-11-0196 upper rubber suction plate is the direct cover: 125 x 75 x 17 mm, 75 mm across width B, grey rubber, big-hole version. It is the surface that touches the panel every cycle, so it is the part that wears first. The 4-011-11-0079 cover fits the same 125 x 75 x 17 mm cup and differs only in centre hole diameter. Carton packed, shipped by air, sea or express.

A vacuum cup that loses hold mid-cycle usually has one worn part, not a broken machine: the top rubber suction plate. Three problems repeat in every shop that runs these cups. The pad glazes over and stops sealing without any obvious failure. The operator pries the cover off to check it and tears the sealing lip. A replacement is ordered from a photograph and arrives with the wrong centre hole.

The 4-011-11-0196 upper rubber suction plate is the direct cover for that wear point on 125 x 75 x 17 mm HOMAG vacuum cups used on CNC drilling machines. It sits on top of the cup, contacts the panel and holds the workpiece against shift during drilling and routing. One detail decides the order: HOMAG lists two covers for this cup, 4-011-11-0196 and 4-011-11-0079, identical in outline and different only in the diameter of the centre hole. This is the big-hole version.

Thickness is 17 mm overall and width B is 75 mm, so the plate drops onto the existing cup without changing pod height or re-teaching a program. Rubber rather than a hard disc means the contact line conforms to the panel and recovers after each vacuum cycle.

Supplied in a carton and shipped by air, sea or express. Price on request against the part number.

Nine facts decide whether this cover fits your cup.

• Big-hole version — this is 4-011-11-0196, the large centre-hole cover; 4-011-11-0079 shares the same outline and differs only in hole diameter.
• 125 x 75 x 17 mm footprint — length 125 mm, width 75 mm, thickness 17 mm, matched to the standard 125 x 75 mm HOMAG cup.
• 75 mm across width B — the B dimension is 75 mm, the figure to quote when you check a cup against a drawing instead of a photograph.
• Rubber body — moulded rubber, not a hard polymer disc, so the contact line conforms to the panel and recovers after every vacuum cycle.
• Grey face shows wear — the grey rubber glazes and crazes before it lets go, so a worn plate is visible at one inspection instead of dropping a panel mid-shift.
• Upper plate only — this is the top cover of the cup, not the lower plate and not the cup body; the valve insert stays in place.
• HOMAG CNC drilling machines — used on HOMAG CNC drilling machines and on CNC router processing centres running the same 125 x 75 mm cup.
• Carton packed — pads ship flat in cartons, so they arrive uncreased and go straight onto the shelf as spares.
• Replaced on its own — a single wear part: cup body, locating ring and gaskets stay in service.

You can keep running a glazed pad and scrap panels, order a complete vacuum cup, or replace the 4-011-11-0196 cover by itself. This part is the third option.

• Replace the wear part, not the assembly. The plate is what contacts the panel, so a pad swap restores grip for the cost of one part instead of a whole cup.
• One part number, no guesswork. 4-011-11-0196 is the big-hole cover for the 125 x 75 x 17 mm cup; the other cover for the same cup is 4-011-11-0079, so the pair can be ordered together.
• No pod re-setting. 17 mm thickness and 75 mm width B match the existing cup, so pod height and program stay untouched after the swap.
• Same outline on both variants. Because 4-011-11-0196 and 4-011-11-0079 share the 125 x 75 mm outline, a wrong-hole mistake costs one part, not a machine stop.
• A consumable you can keep on the shelf. Carton packed, 125 x 75 x 17 mm flat, so 4-011-11-0196 stores as a shelf item next to the cups it fits.
• Confirmed by dimension, not by photo. Three numbers settle the fit: 125 mm, 75 mm, 17 mm.

4-011-11-0196. This listing is the big-hole version of the upper rubber suction plate. 4-011-11-0079 is the other cover for the same 125 x 75 x 17 mm cup and differs only in the diameter of the centre hole.

Yes, if the cup takes a 125 x 75 x 17 mm cover. Measure the old plate across its length, width and thickness and compare against 125 mm, 75 mm and 17 mm; the outline is what fixes the fit, not the part number on the cup body.

No. The plate is a separate top cover, so it comes off on its own. The cup body, valve insert, locating ring and gaskets stay where they are and a pad swap puts the cup back into service.

Only the centre hole diameter. Both are 125 x 75 x 17 mm rubber covers for the same HOMAG cup; 4-011-11-0196 is the big-hole one, 4-011-11-0079 the smaller hole. The outline, thickness and colour are the same.

Rubber, in grey. The grey face is useful in service: glazing and fine crazing show up before the pad stops sealing, so wear is checked by eye rather than by a lost panel.

HOMAG CNC drilling machines, and CNC router processing centres that run the same 125 x 75 mm cup. Application is CNC machining of panels, where the cup has to hold the workpiece without shift during drilling and routing.

Carton packed, by air, by sea or by express. Pads travel flat in the carton, so they arrive uncreased and can go on the shelf as spares next to the cups they fit.

Send the part number and the quantity you need. Price is quoted against 4-011-11-0196; if you also run the smaller-hole cover, quote 4-011-11-0079 on the same enquiry and the two ship together.