132*146*29mm Grey Durable Cnc Vacuum Pods For Flat Table Cnc Biesse Woodworking Spare

Replacing a worn block on a Biesse flat table should not mean re-levelling the whole grid. This is the full-size pod: 132 x 146 mm across the top face, 29 mm high, in grey, moulded from plastic with a rubber contact face, part number 38230559. The base body drops into the existing holding fixture on a pod-and-rail table and can be set at different angles. Half size 75 x 132 mm and 1/3 size 54 x 132 mm bodies are produced alongside it, so one source covers every position on the grid.

A shop running a Biesse flat table meets three things when a pod wears: the seal line opens and a panel shifts mid-cut, the replacement block arrives a size class off so the grid is levelled again, and a small part is held on a cup wider than the part. This pod answers all three.

It is a Biesse vacuum suction block, the full-size body of a three-size family: full size, 75 x 132 mm half size and 54 x 132 mm 1/3 size, with the half and 1/3 bodies also produced in different heights. This one is 132 x 146 mm across the top face, 29 mm high, grey, plastic with a rubber contact face, part number 38230559.

Raising the material off the table is the point: solid wood work and edge detail stay possible because the cutter no longer reaches the grid. The same cup holds large parts, or can be sectioned off with a gasket so a smaller part keeps its own zone. The base body is inserted into a holding fixture on a pod-and-rail table and can be positioned at different angles.

Rubber pads, gaskets and locating rings are listed separately for the same positions, including the white nylon locating ring that supports the block under a Biesse cup. Price is quoted per order.

These are the numbers that decide whether the block seats in your grid.

• Full-size top face - 132 x 146 mm of sealing face, the widest of the three sizes, so a panel sits on a broad ring.
• 29 mm body height - the height to match before ordering: a taller body lifts the grid out of level.
• Three-size family - full size, 75 x 132 mm half size and 54 x 132 mm 1/3 size, produced in different heights.
• Plastic body, rubber face - 2 materials doing two jobs: a moulded body that holds its shape, a rubber face that closes the seal.
• Grey moulding - one colour supplied, easy to spot against a pale panel during a 1-minute walk-round of the table.
• Indexable on the fixture - the base body drops into the holding fixture and the cup can be set at different angles.
• Section it off - one gasket splits a shared zone into a smaller dedicated zone, without re-piping the table.
• Solid wood and edge detail - raising the workpiece off the table clears the cutter on both operations.
• Matching consumables - rubber pads, gaskets and locating rings, including the white nylon support ring under the cup.

The usual choice on a worn full-size pod is between running it until a large panel shifts, and buying a different size class that then has to be shimmed back to level. Neither is a good trade.

• Buy the size class you already run. The 132 x 146 mm full-size body is ordered on its own, so the fixture stays where it is and the table is not re-levelled after a 29 mm part is swapped in.
• One family, every position. 3 top faces - full size, 75 x 132 mm half and 54 x 132 mm 1/3 - cover large panels and small parts from a single stock line.
• A tired seal is a pad order. Rubber pads and gaskets are listed as separate consumables, so a worn contact face costs one small part rather than a complete block.
• Table space back. Sectioning a zone with a gasket, or dropping to a 75 x 132 mm body, keeps a full-size cup free for the next panel, so fewer pods carry the whole job.
• Ordering by number. 38230559 plus 132 x 146 mm and 29 mm are the three checks that stop the wrong body arriving on site.
• Fewer purchase lines. Pads, gaskets and the white nylon locating ring are sourced with the block, so 1 order covers the whole replacement.

Only if your fixture currently takes a full-size body at 132 x 146 mm and 29 mm height. It is listed as a spare for the Biesse flat table and its base body is inserted into the existing holding fixture on a pod-and-rail table, so measure the block you are removing before ordering.

132 x 146 mm across the top face and 29 mm high, part number 38230559, colour grey. It is the full-size body of a family that also includes 75 x 132 mm half size and 54 x 132 mm 1/3 size.

Both, in different places. The body is moulded plastic, which holds the 132 x 146 mm shape while the pump pulls, and the contact face is rubber, which is what seals against the panel. Replacement rubber pads and gaskets are available separately.

Not always. You can section the existing zone off with a gasket, or move to the 75 x 132 mm half size or 54 x 132 mm 1/3 size body when the part is genuinely narrow; sectioning keeps the same block and adds one gasket.

Yes. The base body is inserted into a holding fixture on a pod-and-rail table, and the suction cup can be positioned at different angles in that fixture, so the ring follows the shape of the part.

The rubber pad, the gasket and the locating ring, in most cases. The white nylon locating ring sits on the bottom of a Biesse cup and acts as a support ring for the block, and all three are supplied as separate spares for the same positions.

No set is needed. The block is the part that gets replaced, while pads, gaskets and locating rings are listed as separate consumables, so the positions still holding vacuum keep the height they are already set to.

Price is quoted per order, so the figure depends on quantity and destination rather than a fixed figure on the page. A mixed order of full, half and 1/3 size bodies can be quoted together.