132*146*48MM CNC Vacuum Cups Biesse Vacuum Suction Pods CNC Router Spare Parts

Need a direct replacement for a worn suction pod on a Biesse Rover or point-to-point table? This pod measures 132 x 146 mm on the top face, stands 48 mm tall, and cross-references to Biesse part numbers 6308A0157 and 1614A0118, so it drops onto the existing grid without modification. Plastic body, rubber working face, brown as standard, grey on request. Valve inserts, support rings and gasket seals are available separately, and the same footprint also comes in 29 mm and 74 mm heights. Lead time 1 to 7 working days.

A shop running a Biesse Rover or point-to-point machining center hits the same three things: pods that have gone hard and stop holding a panel, a table setup that will not lift small parts clear of the surface, and a replacement order that arrives after the delivery date has passed. All three are the same block under the panel.

This pod is the direct-fit answer: 132 x 146 mm on the top face, 48 mm tall, so it seats on the standard Biesse grid and lifts the workpiece clear of the table for solid wood edge work and for small parts cut off the bed. Cross-referenced to Biesse 6308A0157 and 1614A0118, one footprint covers machines built in different years.

The body is moulded plastic and the working face is rubber, which is the part that wears. Brown is standard, grey also available. Where a pod has to hold a small part on its own, a gasket seal sections the vacuum grid down to a single 132 x 146 mm pocket.

The 48 mm height sits in a family of three: 29 mm, 48 mm and 74 mm. Valve inserts, support rings and gasket seals are separate line items, so a worn face is replaced without scrapping the block behind it. Supplied from China with a 1 to 7 working day lead time.

What makes this a straight swap for a worn Biesse block:

• 132 x 146 x 48 mm envelope. Top face is 132 x 146 mm, overall height 48 mm, the same envelope as the block it replaces.
• Two Biesse part numbers. Ordered against 6308A0157 or 1614A0118; both numbers sit on this one 48 mm size.
• Fits Rover and point-to-point tables. Listed for Biesse Rover routers and Biesse point-to-point machining centers.
• Three heights in one range. 29 mm, 48 mm and 74 mm, so the pod height follows the cutter.
• Full, half and one-third footprints. Full 146 x 132 mm, half 75 x 132 mm, one-third 55 x 132 mm, all at the same 48 mm height.
• Plastic body, rubber face. The load goes through the moulded plastic block; the wear surface is a separate rubber pad.
• Gasket that sections the grid. One gasket isolates a 132 x 146 mm pocket, so small panels hold without blanking the whole table.
• Wear parts sold separately. Valve inserts, support rings and gasket seals are their own line items, not part of a sealed assembly.
• Brown or grey. Brown as standard, grey on request, so new pods match a set already on the machine.
• Work lifted off the bed. 48 mm of clearance for solid wood edge detail and for cutters that must clear the table surface.

When a pod goes soft, the usual choice is an OEM order on the factory's own schedule or a used block with unknown hours on it. This size makes both of those avoidable.

• Back on the table in days. Lead time is 1 to 7 working days, so a stalled machine is measured in days, not in weeks of waiting.
• One block, two part numbers. Whether the machine was built around 6308A0157 or 1614A0118, the same 132 x 146 x 48 mm block goes back on the grid.
• Small parts stop pulling air. A gasket seal cuts the grid down to one 132 x 146 mm pocket, so a small panel holds as firmly as a full sheet.
• Replace the face, keep the block. Valve inserts, support rings and gasket seals are separate items, so the 48 mm body does not go in the bin with the rubber.
• Height matched to the work. 29 mm for low profiles, 48 mm for general routing, 74 mm where the cutter needs headroom over the bed.
• New pods that match the old set. Brown as standard and grey on request, so one worn pod does not leave the table looking like two different sets.

Yes, if your table takes a 132 x 146 mm pod at 48 mm height. Rover routers and point-to-point machining centers are the two machine families this block is listed for, so measure the footprint and height of the pod you are pulling out before ordering.

Either. Both numbers are listed against this one 132 x 146 x 48 mm pod, so a machine that was built around either number takes the same block.

132 x 146 mm on the top face and 48 mm overall height. The body is moulded plastic, the working face is rubber, and brown is the standard colour.

No. The same construction comes in 29 mm, 48 mm and 74 mm, so a shorter or taller pod is available for the same grid.

Yes, with a gasket seal. The gasket isolates a single 132 x 146 mm pocket; without it the open grid pulls air past the part and the panel moves.

No. Valve inserts, support rings and gasket seals are sold separately, so the worn face is replaced on its own and the plastic block stays in service.

No. They are replacement pods listed against the Biesse part numbers 6308A0157 and 1614A0118 for Rover and point-to-point tables.

1 to 7 working days, from China. Air, sea and express are all used, and the method follows the order quantity.