Biesse Brown 132*54*48mm Cnc Vacuum Pads For Woodworking Machine Parts

Replacing a worn pod on a Biesse nesting table? This brown vacuum pad measures 132 x 54 mm on the top face and 48 mm high, so it takes the console position of the pad it replaces. A valve inside releases suction only when a panel is placed, and a dummy cap shuts the seats you are not using. The same footprint is produced in 29 mm, 48 mm and 74 mm heights, so one order re-pads a mixed table.

A nesting table loses vacuum in three predictable places: a pad sunk below the support plane, a fixture left open with no panel on it, and a replacement cup built to a different height. The 132*54*48 mm brown pad answers all three - a 132 x 54 mm top face, a 48 mm body, and the same heights as the original Biesse pods, so it seats where the old pad sat.

It is a vacuum suction pad for Biesse CNC routers, including Rover and Point to Point machines. A valve inside the pad keeps the vacuum closed until a workpiece is placed on it, so a console not in use stays sealed instead of bleeding air through an open seat. Unoccupied fixtures are closed with a dummy cap, which keeps dust out of the valve and shuts the vacuum off there while the rest of the table keeps holding.

Three service items come with it - valve insert, locating ring and gaskets - so a worn seal is replaced on its own. Because the pad is produced in the same heights as the original cups, 29 mm, 48 mm and 74 mm, old and new pads can be combined on one table without re-levelling the grid. Full, half and one-third size pads are offered in those three heights; packing is standard export cartons and price is quoted per order.

The numbers below decide whether the pad seats without re-shimming.

• Top face matched to the console - 132 x 54 mm contact area, so the pad lands in the same seat as the part it replaces.
• Three heights, one footprint - 29 mm, 48 mm and 74 mm bodies share the same top face, so a 48 mm pad is not a shimmed 29 mm one.
• Valve releases on contact - suction opens only when a workpiece is placed, so unused consoles stay sealed and setup time drops.
• Dummy cap for open fixtures - an unoccupied seat is capped in seconds, keeping dust out and shutting the vacuum off in that fixture.
• Full, half and one-third size - 3 pad lengths in the same family, so corner seats and centre seats come from one source.
• Three service parts - valve insert, locating ring and gaskets are listed as separate replacement items.
• Same height as the original - pads are made to the same 3 heights as the Biesse originals, so new and old can be combined at will.
• Brown body, machined face - the sealing face is machined for high precision, and brown keeps a fresh pad visible among used ones.
• Export packing - packed in standard export cartons, shipped by air, by sea or by express.

The usual choice on a worn pad is to run it until a panel shifts, or to swap a whole console set because the height does not match. Neither is necessary with this pad.

• Replace one seat, not the table. The pad is supplied on its own, so a cracked seat costs one part instead of a full console set that has to be re-levelled.
• Height matching stops panel lift. With 29 / 48 / 74 mm bodies on the same 132 x 54 mm face, the replacement lands at the same plane as the pad it replaced.
• Valves cut changeover time. Suction is released only when a workpiece is on the pad, so a job change needs seconds per console rather than a re-plumb of the table.
• Open fixtures stop leaking vacuum. A dummy cap closes an unused seat in seconds and keeps dust out of the valve, so the pump holds panels instead of air.
• Service parts, not whole assemblies. 3 items - valve insert, locating ring, gaskets - are listed separately, so a worn gasket does not scrap the pad.
• One family covers the table. Full, half and one-third size pads in 3 heights come from one source, so corner and centre positions are matched.
• Packing that survives export. Standard export cartons, with air, sea or express shipping chosen for each order.

Yes, if your console takes a 132*54*48 mm pad. It is listed for Biesse CNC routers, including Rover and Point to Point machines, and the top face is fixed at 132 x 54 mm with a 48 mm body, so measure the pad you are pulling off before ordering.

132 x 54 mm on the top face, 48 mm high. Overall size is quoted as 132*54*48 mm and the same top face is also produced in 29 mm and 74 mm bodies.

Height only. All three share the same 132 x 54 mm top face, so the version you need is set by the height of the pad currently in that seat, not by its width.

No. The pads are made to the same heights as the original Biesse cups, so a single new pad can be combined with the pads already on the table without re-levelling the grid.

It holds the vacuum closed until a panel is placed. That means an unused console stays sealed, and fixtures that are not holding a panel can be closed with a dummy cap that also keeps dust out of the valve.

Yes. All three are listed as available accessories, so a worn gasket or ring is replaced on its own instead of the whole pad being scrapped.

Yes. The pad comes in full size, half size and one-third size, and each of them is produced in the 29 mm, 48 mm and 74 mm heights.

Price is quoted per order, so the figure depends on quantity and destination. Pads are packed in standard export cartons and shipped by air, by sea or by express.