130x30x100mm Q CNC Vacuum Blocks Vacuum Cups Cnc For Smooth Woodworking Tables

Need a replacement block for a 130 x 30 mm seat on a smooth woodworking table? VCB312 is that block: 130 x 30 mm top face, 100 mm body height, top face arranged crossways, grey rubber pad on a plastic body, on a 2-circuit vacuum system. It screws into the seat of the worn suction plate, so the pod, hose and valve stay on the table. Article number 10.01.12.00059, type VCEL-K2 130*30*100Q, lead time 1-7 work days, price on request.

A vacuum table loses its grip in three ways, and every one of them costs machine time. One block stops sealing, so the panel lifts at that corner and the cut drifts out of position. The hold-down height creeps, and a program that ran clean last week now leaves a shoulder on the edge. Then the spindle stops while somebody hunts for a spare.

VCB312 is the block that goes back into that seat: a 130 x 30 x 100 mm CNC vacuum block, also listed as a CNC vacuum cup, with a 130 x 30 mm upper rubber suction pad, a 100 mm body and the top face arranged crossways. Grey rubber and plastic, built for a 2-circuit vacuum system, and listed as a fast, easy and cost-effective replacement of suction plates.

Fit is decided by three numbers, not by the machine badge: the pad at 130 mm by 30 mm, the body at 100 mm, and the direction the long side runs - crossways is what this block is. It is listed against German and Italian CNC woodworking machinery such as Homag.

Article number 10.01.12.00059, type VCEL-K2 130*30*100Q, shipped from Foshan, Guangdong, China in 1-7 work days. Price on request: send the machine model and how many blocks are on the table, and the quote comes back for the right quantity.

What the three dimensions and two materials do in use:

• 130 x 30 x 100 mm — 130 mm pad length, 30 mm pad width and 100 mm body height decide whether the block seats.
• Crossways top face — the long side of the pad runs across the machine axis - the arrangement this block is moulded for.
• Grey rubber pad, plastic body — the rubber holds the seal against the panel, the plastic body carries the 100 mm working height.
• Screwdriver fit — the block unscrews and the new one screws into the same seat, with no change to the vacuum line.
• 2-circuit vacuum system — built for a dual-circuit table, so both zones keep pulling through one 130 x 30 mm seat.
• Aging resistance — listed as excellent aging resistance: a grey rubber face keeps sealing after months on a warm table.
• Replacement, not a rebuild — listed as fast, easy and cost-effective replacement of suction plates: pod body, hose and valve stay on the table.
• German and Italian machines — listed for CNC woodworking machinery such as Homag, where this seat is common.
• Smooth tabletops — meant for smooth woodworking tables, so the pad seals on a flat surface, not across a worn one.
• 1-7 work days — from Foshan, Guangdong, China - the number that decides how many blocks you stock.

The usual answer to a block that stops holding is to keep running it, or to stop and wait for a spare. A block this size changes that calculation:

• A spare in the drawer, not a shutdown. At 130 x 30 x 100 mm the block costs shelf space rather than capital, so a failing seat becomes a swap instead of a stopped spindle.
• The pod stays on the table. Only the suction plate is replaced, so nothing has to be re-levelled or re-hosed before the next panel goes on.
• Panel height stays where the program expects it. The 100 mm body sets how far the panel sits above the table, so a working program keeps working.
• Fit settled with a rule. 130 mm, 30 mm, 100 mm and crossways: four facts read off the old block, before any money is spent.
• A consumable price, not a capital one. The block is the cheapest part of the vacuum assembly and the part that fails first, so money on blocks saves panels and shifts.
• One line of spares. Homag-class German and Italian machines share this seat, so two machine brands do not need two boxes of parts.
• Grey, so wear shows. A rubber face gone shiny or set in one zone is easy to spot, which is the day you swap it.

Only if the three numbers match. The upper rubber pad has to measure 130 x 30 mm, the body 100 mm, and the long side of the pad has to run crossways. Measure the old block before ordering, because the machine badge alone does not settle it.

No. VCB312 is the block with its upper rubber suction pad. The pod body, the hose and the valve stay on your table and are not part of this item.

No. A screwdriver is enough. The block unscrews from the seat and the replacement screws down in the same place, with no change to the vacuum line.

Because the pad is not square. At 130 x 30 mm it is more than four times longer than it is wide, so it only seats one way round - turned along the machine axis it will not line up with the seat.

Rubber and plastic. The rubber pad is the sealing surface against the panel and the plastic body carries the 100 mm height.

Yes. VCB312 is listed for a 2-circuit vacuum system, so both circuits pull through the same seat instead of one zone going dead with the block.

German and Italian CNC woodworking machinery such as Homag. If your machine is not one of those, measure the old block first and compare the three numbers.

1-7 work days from Foshan, Guangdong, China, and one block covers one seat. Count the seats that are not holding, order that number, and the price comes back on request.