10.01.12.00769 120x50x50mm Cnc Vacuum Suction Cup - Vacuum Suction Block Manufacturer

This is the 120 x 50 x 50 mm lengthways vacuum block that holds narrow parts down on a pod and rail console table. Art number 10.01.12.00769, type VCBL-K2 120*50*50 L, one vacuum circuit, 50 mm tall, top rubber pad 120 x 50 mm. It is listed for Homag, Weeke, Holz-Her, CMS, IMA, Masterwood, Felder, Reichenbacher, Busellato, Format 4 and Anderson console tables, and arrives as a complete set. Bulk packed, origin China, price on request.

A pod and rail table only earns its keep while the blocks on it still seal. Three failures keep coming back: a narrow rail leaves too little rubber under the panel, a torn top pad takes an otherwise sound block out of service, and a block bought on size alone turns up with the wrong footprint for the console. This block is aimed at all three.

The 10.01.12.00769 is a 120 x 50 x 50 mm vacuum suction cup, catalogued as a vacuum suction block and also sold as a Schmalz vacuum block. Type is VCBL-K2 120*50*50 L: rubber top pad 120 x 50 mm, body height 50 mm, lengthways arrangement, one vacuum circuit per block, for a 1-circuit console CNC table.

It is listed for the pod and rail console machines most panel shops run: Homag, Weeke, Holz-Her, CMS, IMA, Masterwood, Felder, Reichenbacher, Busellato, Format 4 and Anderson. The lengthways layout runs the 120 mm face along a narrow rail, so the rubber sits under the part instead of beside it.

Each block ships as a complete set, so nothing has to be matched from three order lines. Top rubber pads and bottom vacuum pads are stocked as separate replacements, which turns a worn sealing edge into a pad order. Origin is China, packing is bulk, and the price is quoted per order.

One art number, two wear parts, and a footprint fixed by two numbers.

• Complete set, one art number — body, top rubber pad and bottom vacuum pad ship together under 10.01.12.00769, so a changeover is one line on the purchase order.
• Top pad 120 x 50 mm — the rubber face that meets the panel is stated before ordering, not scaled from a listing photo.
• Height 50 mm — the second number a console position has to match, measured on the body, so table height is unchanged after a swap.
• Lengthways (L) arrangement — the 120 mm side runs along the rail, the layout narrow rails and short panels need to stay clamped.
• One vacuum circuit per block — built for 1-circuit console CNC tables, the Schmalz-style console layout this block is catalogued against.
• Two replaceable wear parts — top rubber pads and bottom vacuum pads are stocked separately, so a torn lip costs one pad instead of one block.
• Eleven-name fit list — Homag, Weeke, Holz-Her, CMS, IMA, Masterwood, Felder, Reichenbacher, Busellato, Format 4 and Anderson console tables.
• Second art number 10.01.12.03549 — listed in the specification block for this page, so a fitter can check the order against either number.
• Bulk packed, origin China — packed in bulk for workshops that buy vacuum pods by the set rather than by the piece.

The real decision on a pod and rail table is not which brand of block to buy. It is whether a tired block gets re-padded or written off, and how long the table stands still while somebody decides.

• A worn edge costs one pad, not one block. Top rubber pads and bottom vacuum pads are both sold separately, so the body stays on the table and only the sealing face is replaced.
• No re-setting after a swap. A 120 x 50 mm plate at 50 mm height keeps the console position at the same footprint and the same height, so the operator does not re-zero the table.
• Clamping on narrow rails. The lengthways 120 mm face runs along the rail, which is where a wider block would hang past the panel edge and clamp nothing.
• One spares list for a mixed-brand floor. Homag, Weeke, Holz-Her, CMS, IMA, Masterwood, Felder and Busellato consoles all sit on the fit list, so one stock line covers several machines.
• Complete set on arrival. Body, top pad and bottom pad come together, so a block is not held in the stores waiting for a missing pad.
• Two numbers to check the order against. 10.01.12.00769 and 10.01.12.03549 both identify this block, which cuts the chance of a 120 x 50 x 50 mm pod being picked when another size was meant.

Yes, if the console runs 1-circuit pods with a 120 x 50 mm top pad. The block is 50 mm tall, type VCBL-K2 120*50*50 L, and it is listed for Homag, Weeke, Holz-Her, CMS, IMA, Masterwood, Felder, Reichenbacher, Busellato, Format 4 and Anderson pod and rail tables.

The whole block. It ships as a complete set with the body, the top rubber pad and the bottom vacuum pad, so it can go straight onto the console.

Both numbers are listed for this 120 x 50 x 50 mm block, and both are printed here so either can be quoted. 10.01.12.00769 is the number in the product name; 10.01.12.03549 is the art number in the specification block. Send either plus the quantity and the block is confirmed against your console before it ships.

Yes. Both are stocked as separate replacements, so a worn or torn sealing face is a pad order rather than a new block.

It means lengthways. The 120 mm side of the pad runs along the rail, which is the arrangement used for clamping narrow parts; the block is 50 mm tall in either case.

Yes, one block per vacuum position. Each block carries a single vacuum circuit, so every console position that had a block gets one block back.

CMS, IMA, Masterwood, Felder, Holz-Her, Reichenbacher, Busellato, Format 4 and Anderson, plus other console tables. The full fit list is in the parameter table above, and a photo of the block you are replacing settles it fastest.

Bulk packed, price quoted per order, origin China. Send the quantity, the machine model and the art number you order by, 10.01.12.00769 or 10.01.12.03549, and the quotation comes back against this exact 120 x 50 x 50 mm block.