130x30x50 L Replaceable Cnc Suction Pods Cnc Vacuum Pods For Woodworking Machine

One leaking pad stops a whole machining centre, and the block is usually the part at fault, not the table. VCB306 is that block: 130 x 30 x 50 mm, longways arrangement, 2-circuit console system, plastic body with replaceable rubber top and bottom faces, art.-no. 10.01.12.00647, type VCEL-K2 130x30x50 L. It is clamped onto the console, sealed to the panel by the second vacuum circuit, and listed for Homag, Biesse and Felder CNC machines. Packed bulk. Price on request.

A console table fails in three ways, and all three cost shift time. One pad stops sealing, so the panel lifts at that corner and the cut drifts. The pad sits lower than it did, so a program that ran clean yesterday leaves a step in the edge. Then the spindle waits while somebody walks to the store for a spare.

VCB306 is the block that ends that walk: a 130 x 30 x 50 mm suction pod, also listed as a vacuum block or Schmalz vacuum block, made for consoles running a 2-circuit vacuum system. The body carries a 130 x 30 mm top face set longways, 50 mm high, so it repeats the working height the program expects. Top and bottom rubbers are replaceable: a glazed face comes off, a new one goes on, and the plastic body stays clamped.

Blocks are pre-fixed to the console and clamped, so none of them creeps while panels are loaded. The first circuit holds the block to the console, the second holds the workpiece to the block, which keeps both joints sealed under a panel being cut.

Fit is settled by three numbers - 130 mm long, 30 mm wide, 50 mm high - and by the longways direction of the face. Listed for Homag, Biesse and Felder machining centres, packed bulk, shipped by air, sea or express. Price on request.

What the three dimensions, two rubbers and two circuits do once the block is on the console:

• 130 x 30 x 50 mm — 130 mm long, 30 mm wide, 50 mm high: the three numbers that decide whether the block seats on your console.
• Longways top face — the 130 mm side of the 130 x 30 mm face runs along the console rail, which is the arrangement this block is built for.
• Replaceable top and bottom rubbers — two sealing faces, both replaceable: the top face seals the panel, the bottom face seals on the console.
• 2-circuit console system — one circuit clamps the block down, the second clamps the panel, so both joints are held at the same time.
• Hose-free block — the blocks are pre-fixed on the console, so no vacuum hose runs to each of them.
• Plastic body, rubber faces — the body stays on the table; the rubbers are the parts that wear.
• 50 mm working height — the height sets where the panel sits, and every block on the table repeats it.
• Taller 130 x 30 x 100 mm pod — the same supply carries a 100 mm high pod where the panel has to sit higher.
• Bulk packing, three shipping routes — blocks ship bulk by air, sea or express.

The usual choice on a leaking pad is to keep running it or to stop the machine and wait for a spare. A block with replaceable rubbers changes that calculation:

• Rubbers off, body stays. Only the two sealing faces are replaced, so the block does not have to be re-clamped or re-levelled before the next panel goes on.
• Height stays where the program expects it. A 50 mm body with a 130 x 30 mm face repeats the setup, so the program that ran last week still runs.
• Two wear parts, not a whole block. Top and bottom rubbers are the consumables, so one set of pads keeps every 130 x 30 x 50 mm block on the table sealing.
• Both joints held at once. The block is clamped to the console and the panel is clamped to the block, so the part cannot slide while it is being cut.
• Fit settled by three numbers. 130, 30, 50, plus the longways direction - measured off the old block before any money is spent.
• One spare line for three machine builders. Homag, Biesse and Felder consoles are all listed against VCB306, so a mixed shop does not need a second spare part number.
• Order size matches the table. Bulk packing and three shipping routes keep a replacement order in step with the number of blocks in use.

Only if the three numbers match. The block has to measure 130 x 30 x 50 mm and the long side of the top face has to run longways; check the old block with a rule before ordering, because the machine badge alone does not settle it.

No. Both the top and the bottom rubber are replaceable, so a glazed or cut face is swapped and the plastic body stays on the console.

Two separate vacuum paths. One circuit clamps the block down to the console and the second clamps the workpiece down to the block, so the block and the panel are held independently.

It is the L version, longways. The 130 mm side of the face runs along the console rail; a crossways block is a different arrangement and will not line up with the same seat.

The height. This block is 50 mm high and the 100 mm pod raises the panel by another 50 mm, so choose the height that matches the setup your program was written for.

Homag, Biesse and Felder machining centres. If your machine is not on that list, measure the old block at 130 x 30 x 50 mm and compare the arrangement before ordering.

Plastic body with rubber sealing faces, packed bulk. Blocks travel by air, sea or express, so the shipping method follows the size of the order.

Price on request. Send the machine model and the number of blocks on your console, and the quote comes back against the right quantity and the right arrangement.