120x50x50mm CNC Vacuum Cups Vacuum Suction Blocks For CNC Woodworking Machine

Looking for a replacement for a VCBL-K1 120x50x50 Q vacuum block without sitting out an OEM order? This is it: 10.01.12.00770, a grey vacuum suction block with a 120 x 50 mm top plate and 50 mm height for 1-circuit console CNC routers on a pod and rail table. It arrives as a complete set, plastic body with rubber top and bottom pads, and the two wear pads (10.01.12.00012, 10.01.12.00228) can be reordered on their own. Lead time is 1 to 7 work days.

A pod and rail table only pays for itself while the blocks on it still hold. Three things go wrong most often: the original pods stop sealing, one cracked pad writes off a block that is otherwise sound, and the replacement that finally arrives has a footprint that does not match the console it was ordered for. The 10.01.12.00770 block is built around those three failures.

It is a grey 120 x 50 x 50 mm vacuum suction block for 1-circuit console CNC routers with a pod and rail table. It is listed as the replacement for the VCBL-K1 120x50x50 Q block, so the top plate is 120 x 50 mm and the body stands 50 mm tall; those two numbers are what decide whether a block sits flat on your console.

The body is plastic and both sealing faces are rubber, and the block ships as a complete set: body, top rubber pad, bottom vacuum pad. The wear parts are also stocked on their own, top pad 10.01.12.00012 and bottom pad 10.01.12.00228, so a worn lip costs you a pad instead of a whole block.

Fit covers the German and Italian console machines most pod and rail shops run: Homag, Weeke, Felder, Masterwood, Busellato, Biesse and SCM. Origin is China, lead time is 1 to 7 work days, and orders ship by air, by sea or by express.

One art number, one complete block, and two wear parts you can reorder on their own.

• Complete block, one art number. Body, top pad and bottom pad arrive as a set under 10.01.12.00770, so a changeover does not depend on matching three separate order lines.
• Top plate 120 x 50 mm, height 50 mm. The two dimensions that set console fit are fixed before ordering, not estimated from a photo.
• Two reorderable wear parts. Top pad 10.01.12.00012 and bottom pad 10.01.12.00228 are stocked as separate items.
• Rubber faces on a plastic body. The rubber lip seals and the plastic body carries the 50 mm height.
• Made for 1-circuit console tables. One vacuum circuit per block, pod and rail table, the layout the Homag and Weeke console machines in the fit list use.
• Narrow 120 x 50 mm face. A small footprint for narrow rails and short panels, where a wider block would run past the panel edge and clamp nothing.
• Grey, so the rack sorts itself. Every block reads the same colour, which keeps mixed sizes from being fitted into the wrong console position.
• Fit list on the label. Homag, Weeke, Felder, Masterwood, Busellato, Biesse and SCM console machines.
• 1 to 7 work days. Stocked as a standard item and shipped by air, by sea or by express to suit the order size.

The real choice on a pod and rail table is not brand against brand, it is whether a tired block gets replaced or re-padded, and how long the table stands idle while you decide.

• Re-pad instead of re-buy. Two pads carry the vacuum, each with its own art number, so a worn lip costs one pad and the body stays on the table.
• One line on the purchase order. The complete set ships under a single art number, so the body and the pads on your table are always the same generation.
• Same footprint as the block you pull off. 120 x 50 mm plate at 50 mm height means the console positions do not have to be re-set after the swap.
• Mixed-brand floor, one supplier. Homag, Weeke, Biesse and SCM consoles take the same family of blocks, so one spares list covers the whole cell.
• Downtime counted in days, not shipments. Lead time is 1 to 7 work days before the freight leg even starts.
• Fewer wrong-fit returns. Footprint, height and circuit type are all stated, so a fitter can confirm the block before the clamp is closed.

Yes, if your console runs 1-circuit pods with a 120 x 50 mm top plate. The block is a replacement for the VCBL-K1 120x50x50 Q and carries the same 120 x 50 mm plate and 50 mm height.

The whole block. It ships as a complete set with the plastic body, the top rubber pad and the bottom vacuum pad.

Yes. The two wear parts are separate items: top rubber pad 10.01.12.00012 and bottom vacuum pad 10.01.12.00228.

Nothing, they are the same block. VCB301-120x50x50 is the model code and 10.01.12.00770 is the art number to put on the order.

Rubber sealing pads on a plastic body. The rubber does the sealing and the plastic body holds the 50 mm height, in grey.

1 to 7 work days for the goods, then the freight leg. The block is a stocked standard item, not a made-to-order part.

Yes. It is listed as the replacement for that block on 1-circuit console CNC routers with a pod and rail table.

Price is quoted per order and shipping is by air, by sea or by express depending on quantity. Send the quantity and the destination and both come back together.