3-607-11-2710 SPROCKET Z 12 06B-1 Woodworking Machinery Tool

This is a 12-tooth sprocket, part number 3-607-11-2710, for Brandt KD, KDN, KDF and Ambition series woodworking machines. It is a 06B-1 chain sprocket, new condition. Check your existing sprocket: count 12 teeth and confirm the 06B-1 chain pitch before ordering. The sprocket meshes with the chain to transmit power; a worn sprocket causes chain slip, noise and uneven feed. Send your machine model and the part number 3607112710 with your enquiry.

When the chain starts jumping teeth or the feed surges, the sprocket is often the first place to look. A worn 12-tooth sprocket will not hold chain pitch, so the chain rides high on the teeth and wears fast. Replacing it restores steady transmission before the chain is damaged.

This is a 06B-1 chain sprocket with 12 teeth, part number 3-607-11-2710. It fits Brandt KD, KDN, KDF and Ambition series machines. To confirm fit, remove the old sprocket and check the tooth count is 12 and the chain is 06B-1. Match the part number 3607112710 against your parts book.

Mounting is straightforward: slide the sprocket onto its shaft, align it with the chain run, and secure it. Check that the chain sits fully in the tooth valleys with no lift. Correct alignment and a new sprocket reduce chain wear and keep feed speed consistent through the cut.

SHUNHONGYU supplies this sprocket as a new part. Shipment is by DHL, FedEx or UPS. When you enquire, send your machine model, the part number 3-607-11-2710 and the quantity you need. SHUNHONGYU supplies various woodworking machine parts, so include any other part numbers you are looking for. Supply comes from the same range as the rest of the catalogue.

What the specification fixes, and what it leaves to the machine:

• Tooth count for feed drive — 12 teeth match the 06B-1 chain pitch so the chain engages every tooth evenly during feed.
• Chain size compatibility — 06B-1 chain is the specified chain for this sprocket, keeping the drive running at the designed ratio.
• Machine fit for Brandt series — Fits Brandt KD, KDN, KDF and Ambition series machines, covering common edgebander and processing models.
• Wear point on teeth — The 12-tooth profile wears at the tooth flanks; replacing the sprocket restores correct chain mesh.
• Installation on shaft — Slides onto the drive shaft and secures in line with the chain run for straight transmission.
• Part number identification — 3-607-11-2710 and 3607112710 are marked for cross-checking against your machine parts list.
• New condition part — Supplied new, so tooth profiles are unworn and ready for installation without rework.
• Chain alignment check — With the sprocket fitted, confirm the chain sits fully in the tooth valleys before running.
• Replacement for worn sprockets — Swap out a worn 12-tooth sprocket to stop chain jump and uneven feed on the machine.
• Shipping options — Ships by DHL, FedEx or UPS, so you can choose the carrier that suits your delivery needs.

What changes on the shop floor when the right part goes back in:

• Stops chain jump. A new 12-tooth sprocket holds the 06B-1 chain at correct pitch, so the chain stops riding high and jumping teeth during feed.
• Restores feed consistency. Worn teeth cause speed variation; fitting this sprocket brings feed back to a steady rate through the cut.
• Reduces chain wear. Correct mesh between the 12 teeth and 06B-1 chain lowers chain wear, extending chain life and cutting replacement frequency.
• Simple fitment check. Counting 12 teeth and confirming 06B-1 chain takes minutes, so you can verify fit before ordering.
• Covers several models. One sprocket fits Brandt KD, KDN, KDF and Ambition series, simplifying stock for mixed machine lines.
• New part readiness. Supplied new, the sprocket needs no rework; install it straight from the box and set chain tension.
• Clear part traceability. Part numbers 3-607-11-2710 and 3607112710 let you match the sprocket to your parts book without guesswork.
• It fits the machine you already run. The sprocket is made for woodworking machines, so it returns to the same shaft, bracket or spindle without re-machining the mounting.
• Downtime measured in minutes, not days. A replacement held on the shelf turns a worn part into a changeover instead of a stopped line.

Check that your machine is a Brandt KD, KDN, KDF or Ambition series and that the old sprocket has 12 teeth. Also confirm the chain is 06B-1 and the part number matches 3-607-11-2710.

It uses 06B-1 chain. The 12 teeth are cut for that chain pitch, so using any other chain size will cause poor mesh and rapid wear.

You can replace the sprocket alone if the chain is still within wear limits. Inspect the chain for stretched links; if worn, replace both to avoid new sprocket wearing fast.

It has 12 teeth. Count the teeth on your existing sprocket to confirm before ordering.

The part number is 3-607-11-2710, also written 3607112710. Quote this number with your machine model when you enquire.

Shipment is by DHL, FedEx or UPS. Tell us your preferred carrier when you place the order.

Send your machine model, the part number 3-607-11-2710 and the quantity required. If you need other parts, include those part numbers too.

Yes, it is supplied new. The tooth profiles are unworn and ready for installation.