Edgebanding Press Rubber Roller Pressure Wheels For Homag Edgebander 70x20x25

This grey rubber press roller fits Homag edgebanding machines and presses tape against the panel edge. It measures 70 mm outer diameter, 20 mm inner diameter, and 25 mm height. The rubber surface grips the banding without marking it. Before ordering, check that your machine's spindle or shaft is 20 mm and the space for the roller is at least 25 mm wide. Confirm the original roller's outer diameter is 70 mm. Send those dimensions and your machine model with your enquiry.

When edgebanding, uneven pressure from a worn or incorrect roller causes glue lines, lifted tape, or marks on the panel edge. A roller that no longer matches the machine's spindle or width can wobble or bind. This press roller addresses that by providing a 70 mm outer diameter, 20 mm inner diameter, and 25 mm height to restore consistent contact.

The PSW051 is a grey rubber press roller for Homag edgebanding machines. Its 70 mm outer diameter, 20 mm inner diameter, and 25 mm height match common Homag setups. To confirm fit, measure your existing roller's outer diameter, inner bore, and width, and check the machine model plate before ordering.

Check that the mounting shaft is 20 mm and that the roller seat accepts a 25 mm width. The rubber surface presses the tape against the panel as the roller turns. A correct bore and width keep the roller running true, so pressure stays even across the tape and the glue line.

Supply is straightforward: the roller is packed as a single unit unless you request otherwise. Customisation is not stated. When enquiring, send the machine model, the dimensions of your old roller (outer diameter, inner diameter, height), and the quantity you need. That lets us confirm the PSW051 matches your setup.

What the specification fixes, and what it leaves to the machine:

• Tape pressure — The 70 mm outer diameter gives a contact area that presses edge tape evenly against the panel during the banding cycle.
• Shaft fit — A 20 mm inner diameter fits spindles or shafts of that size, so the roller mounts without adapters on compatible Homag machines.
• Width clearance — At 25 mm height, the roller fits into the machine's roller seat where the existing width is 25 mm.
• Rubber contact — The grey rubber surface grips the tape without marking it, helping maintain a clean edge finish on the panel.
• Wear point — Rubber rollers wear at the outer diameter over time; replacing at 70 mm restores the original contact profile.
• Machine match — Designed for Homag edgebanding machines, this roller replaces the original when dimensions match the spindle and seat.
• Fit check — Measure the old roller's outer diameter, inner diameter, and height; compare with 70 mm, 20 mm, and 25 mm before ordering.
• Installation — Slide the roller onto the 20 mm shaft and secure it; the 25 mm width sets the roller's position in the seat.
• Glue line — Even pressure from the rubber surface helps keep the glue line consistent along the panel edge during banding.

What changes on the shop floor when the right part goes back in:

• Restores even tape pressure. A worn roller can cause uneven pressure and lifted edges. This 70 mm roller brings contact back to the original profile, so tape bonds consistently.
• Fits common Homag spindles. The 20 mm inner diameter matches shafts of that size, reducing the need for adapters and simplifying replacement on compatible machines.
• Saves setup time. With a 25 mm height, the roller drops into the existing seat without modification, so changeover takes minutes instead of hours.
• Protects panel finish. The grey rubber surface grips without marking, helping maintain a clean edge appearance on finished panels.
• Reduces rejected edges. Correct pressure from the 70 mm outer diameter helps prevent glue lines and lifted tape, lowering rework on banded panels.
• Easy wear check. Measure the outer diameter; when it drops below 70 mm, the roller is worn and due for replacement, making maintenance decisions simple.
• Clear enquiry process. Send your machine model and old roller dimensions; we confirm the PSW051 against your data before you commit to an order.
• It fits the machine you already run. The PSW051 is made for edge banding machines, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Check your machine's spindle size and roller seat. The roller has a 20 mm inner diameter and 25 mm height, and fits Homag machines that use those dimensions. Measure your old roller to confirm.

The roller measures 70 mm outer diameter, 20 mm inner diameter, and 25 mm height. These figures are marked on the product and should match your old roller.

The roller is made of grey rubber. This material provides grip on the tape without marking the panel edge during pressing.

Slide the roller onto the 20 mm shaft and secure it in the roller seat. The 25 mm width sets its position. Refer to your machine manual for specific mounting steps.

Replace it when the outer diameter wears below 70 mm or when you see uneven tape adhesion. A worn roller can cause lifted edges and glue lines.

Customisation is not stated for this product. Send your required dimensions with your enquiry and we will confirm what is available.

Minimum order quantity is not stated. Include the quantity you need in your enquiry and we will respond with details.

The roller is packed as a single unit unless you request otherwise. Packaging details are not specified beyond this.