Warm Reducer Woodworking Machinery Parts Gear Reducer 1:60 Ratio Die Cast

A SHUNHONGYU gear reducer for edgebanders and drilling machines, available in speed ratios 1:60, 1:30, and 1:15. Lifting reducers use 1:60 or 1:30; glue pot reducers use 1:15. The body is aluminum die-casting for efficient heat dissipation. Confirm fit by matching the ratio to the machine function and checking the mounting interface. Send the machine model and required ratio with your enquiry.

When an edgebander's glue pot or a drilling machine's height adjustment starts drifting or losing speed under load, the reducer is often the first place to check. A worn or mismatched unit shows up as inconsistent glue application or inaccurate drilling depth, slowing the line and increasing scrap. Getting the right ratio back on the machine restores repeatable movement.

This is a SHUNHONGYU gear reducer with a body made from aluminum die-casting. Three ratios cover the range: 1:60 and 1:30 for lifting, and 1:15 for the glue pot. It fits edgebanders and drilling machines. To confirm fit, note the ratio stamped on the old unit and the mounting pattern, then compare with the machine's parts list before ordering.

Check the shaft and flange dimensions against the old reducer, and make sure the ratio matches the function: lifting reducers run 1:60 or 1:30, glue pot reducers run 1:15. The aluminum die-casting box helps dissipate heat during long shifts, so the unit runs cooler and holds ratio over extended use.

Supply comes from China. If you need a specific ratio or a small batch, state it clearly. When enquiring, send the machine make and model, the required ratio, the old reducer's label photo, and the quantity. That lets us check the match before you commit to an order, reducing the risk of a wrong fit on the line.

What the specification fixes, and what it leaves to the machine:

• Lifting height control — The 1:60 ratio suits slow, controlled lifting of heavy heads or tables on drilling machines.
• Faster lifting option — A 1:30 ratio gives quicker vertical movement where cycle time matters more than torque multiplication.
• Glue pot speed — The 1:15 ratio is intended for glue pot reducers on edgebanders, matching the required roller speed.
• Edgebander fitment — This reducer mounts on edgebanders and drilling machines, covering two common woodworking machine types.
• Heat under load — Aluminum die-casting box construction aids heat dissipation, helping the reducer stay cooler during long runs.
• Body material — The aluminum die-cast body keeps weight down compared with cast iron while still supporting the gear train.
• Ratio marking — Each unit carries its ratio, so you can verify 1:60, 1:30, or 1:15 against the machine's requirement.
• Mounting check — Confirm the shaft diameter and bolt pattern against the old reducer before fitting to avoid rework.
• Brand consistency — SHUNHONGYU reducers are used across edgebanders and drilling machines, simplifying spares stocking.
• Wear point access — The reducer sits at the drive point, so checking for play or noise is part of routine maintenance.
• Fit — built for woodworking drilling machines, in the position the original part occupied.

What changes on the shop floor when the right part goes back in:

• Match the ratio to the job. Using 1:60 or 1:30 for lifting and 1:15 for the glue pot keeps each function running at its intended speed, avoiding sluggish lifting or glue starvation.
• Cooler running on long shifts. The aluminum die-casting box helps dissipate heat, so the reducer is less likely to overheat during continuous production and cause unplanned stops.
• One spares line for two machines. Because the same reducer family fits edgebanders and drilling machines, you can stock fewer part numbers while still covering both machine types.
• Straightforward replacement. With ratios clearly marked, your maintenance fitter can match the old unit and swap it without guesswork, cutting downtime on the line.
• Aluminum body resists corrosion. The die-cast aluminum construction stands up to shop-floor conditions better than untreated steel, reducing the chance of seizure from rust.
• Stable under vertical loads. Lifting reducers in 1:60 or 1:30 are built for vertical movement, so drilling heads and tables hold position without creeping during operation.
• Clear enquiry process. Send the machine model and ratio, and we check the match before shipping, so you are less likely to receive a reducer that will not fit.

Check the function: glue pot reducers use 1:15, while lifting reducers use 1:60 or 1:30. The old reducer's label or the machine manual will state the ratio. If unsure, send a photo of the old unit with your enquiry.

It fits drilling machines that use a SHUNHONGYU lifting reducer in 1:60 or 1:30. Confirm by comparing the mounting bolt pattern and shaft size with your old unit. Send the machine model and a photo of the old reducer for a check.

Lifting reducers use 1:60 or 1:30 for vertical movement, while glue pot reducers use 1:15 for the glue roller drive. They are not interchangeable because the ratios differ. Order the one that matches the function.

The body is aluminum die-casting. That helps with heat dissipation and keeps the reducer lighter than a cast iron equivalent. It is not a cast iron unit.

Yes, single units can be supplied. State the ratio you need and the machine it is for. We will confirm the match before shipping.

Look for the ratio stamped on the old reducer or in the machine manual. If it is not visible, send a clear photo of the old unit's label with your enquiry.

Send the machine make and model, the required ratio, a photo of the old reducer's label, and the quantity. That lets us verify the fit and reduce the risk of a wrong part.

Yes, the aluminum die-casting box is designed for efficient heat dissipation. That helps the reducer run cooler during long shifts compared with a box that traps heat.