Rubber Pressure Wheel For Cehisa Edgebander Woodworking Machine Spares

Rubber pressure roller for Cehisa edgebanding machines. It measures 60 mm outer diameter, 15 mm inner diameter, and 24 mm thick, made from rubber with a bearing. Buyers confirm fit by checking their Cehisa edgebander uses a 60*15*24 mm pressure wheel and that the old roller matches these dimensions. It presses edging onto panels without slippage. Send your machine model and a photo of the old roller with your enquiry.

When a pressure roller wears or glazes, edging lifts at the ends or drifts off the panel line. On a Cehisa edgebander, the roller must keep steady pressure across the glue line. A worn 60 mm roller can allow slippage, causing reject panels and extra rework.

This rubber pressure roller is a spare for Cehisa edgebanding machines. It measures 60 mm outer diameter, 15 mm inner diameter, and 24 mm thick. The body is rubber, and a bearing sits inside the 15 mm bore. To confirm fit, compare these three dimensions with the roller currently on your machine.

Check the bore and outer face of the old roller before ordering. The 15 mm inner diameter must match the shaft, and the 24 mm thickness must clear the machine frame. The rubber face grips the edging as it passes, so the band stays tight against the panel without slipping.

Supply is straightforward: the roller is a single spare part. If you need a different specification, send the dimensions you require. With every enquiry, include your Cehisa machine model, the 60*15*24 size you need, and a photo of the old roller so the fit can be checked before dispatch.

What the specification fixes, and what it leaves to the machine:

• Edgebander pressure point — The roller applies pressure at the glue line on Cehisa edgebanders, helping the edging bond to the panel surface.
• Direct replacement size — At 60 mm outer diameter, 15 mm inner diameter, and 24 mm thickness, it matches the original fit for Cehisa machines.
• Bearing inside the bore — A bearing sits in the 15 mm inner diameter, allowing the roller to spin freely on the machine shaft.
• Rubber contact face — The rubber outer face grips the edging material as it passes, reducing slip during the edgebanding cycle.
• Wear check made easy — Compare the 60 mm outer diameter with your old roller; a noticeably smaller diameter means the rubber has worn down.
• Shaft fit confirmation — Measure the shaft that the roller mounts on; it must match the 15 mm inner diameter for correct seating.
• Frame clearance check — The 24 mm thickness must clear the machine frame and any guides; measure the old roller to confirm this dimension.
• Cehisa fitment — Made for Cehisa edgebanding machines, this roller is a spare for that model line, not a universal fit.
• Glue line pressure — Steady pressure from the rubber face helps keep the edging tight against the panel through the glue line.

What changes on the shop floor when the right part goes back in:

• Keeps edging tight at the glue line. A worn roller lets the band lift or drift. This 60 mm rubber roller restores pressure so the edging stays against the panel, reducing reject panels and rework.
• Fits Cehisa machines without guesswork. The 60*15*24 mm size is made for Cehisa edgebanders. Buyers confirm the fit by checking the outer diameter, inner diameter, and thickness against the old roller.
• Bearing keeps the roller spinning. The bearing inside the 15 mm bore lets the roller turn on the shaft. That means less drag and a more consistent feed through the edgebanding cycle.
• Rubber face grips without slipping. The rubber outer surface presses the edging onto the panel. With a 60 mm diameter, it holds the band in place as it passes the glue line.
• Simple size check before ordering. Measure the old roller: 60 mm outer, 15 mm inner, 24 mm thick. If all three match, the spare goes straight onto the machine shaft.
• One spare covers a wear point. The pressure roller is a wear item. Keeping a 60*15*24 spare in the spares cabinet means a glazed roller does not stop the edgebander for long.

Check the dimensions first: the roller must be 60 mm outer diameter, 15 mm inner diameter, and 24 mm thick. Measure your old roller or shaft to confirm these three sizes match your machine.

The roller measures 60 mm outer diameter, 15 mm inner diameter, and 24 mm thick. These figures are the full size specification for this spare part.

The roller body is rubber, and a bearing is fitted inside the 15 mm bore. The rubber face contacts the edging, while the bearing lets the roller spin on the shaft.

Replace it when the rubber face is glazed, cracked, or worn down. A 60 mm outer diameter that measures noticeably less means the rubber has worn and pressure may be inconsistent.

This roller is a spare for Cehisa edgebanding machines. For another brand, check that the 60*15*24 mm dimensions match your machine before ordering.

Include your Cehisa machine model, the 60*15*24 size you need, and a photo of the old roller. That information helps confirm the fit before the spare is dispatched.

Yes, the roller is supplied with a bearing inside the 15 mm inner diameter. The bearing is part of the assembly and allows the roller to turn on the machine shaft.

If you need a size other than 60*15*24 mm, send the dimensions you require with your enquiry. The roller can be supplied to the specification you provide.