Premium Manual Glue Tank Replacement for Homag Edge Banding Machine Edgebander Glue Pot

A manual glue tank replacement for Homag edge banding machines, sized 80 × 68 × 14.4 mm, with a 0.8mm X anti-sawdust texture shaft and PT100 thermal probe. The tank is anti-rust cast alloy and the roller is hardened steel. It runs EVA hot melt glue with a 1.5KW heating core. To confirm fit, match the 80 × 68 × 14.4 mm dimensions and manual adjustment gluing unit to your existing tank. Customization is supported.

Uneven glue lines, temperature faults, and leaks from an old tank stop the line. This manual glue tank replaces the worn unit on Homag edge banding machines, restoring consistent EVA hot melt application. The 1.5KW heating core and PT100 probe work together to hold glue temperature during daily production.

This is a manual adjustment gluing unit with an 80 × 68 × 14.4 mm envelope. The tank is anti-rust cast alloy; the gluing roller is hardened steel with a 0.8mm X anti-sawdust texture shaft. It fits Homag edge banding machines. Confirm fit by comparing these dimensions and the manual adjustment knob layout to your current tank.

Check the mounting bolt pattern and wiring port before installation. The manual adjustment knobs let the operator set glue roller position without power tools. Because the shaft carries a 0.8mm X texture, sawdust is pushed aside rather than packed into the glue film, which keeps the coating even across the panel edge.

Customization is supported, so non-standard mounting or port details can be discussed. No packing or lead time is stated here. Send your machine model, the 80 × 68 × 14.4 mm tank dimensions, and a photo of the existing wiring port and knobs with your enquiry. That lets the supplier confirm the manual adjustment gluing unit matches before you order.

What the specification fixes, and what it leaves to the machine:

• Manual glue tank fit — Replaces the manual adjustment gluing unit on Homag edge banding machines, with an 80 × 68 × 14.4 mm envelope for checking against the old tank.
• Anti-sawdust roller face — 0.8mm X anti-sawdust texture shaft on the hardened steel gluing roller pushes sawdust aside to reduce buildup in the glue film.
• Temperature sensing — PT100 high-precision thermal probe reads glue temperature so the 1.5KW heating core can hold EVA hot melt at a steady working condition.
• Tank material — Anti-rust cast alloy tank resists corrosion from daily EVA hot melt glue contact and reduces glue residue buildup on the inner surface.
• Heating core — Standard 1.5KW industrial heating core supplies the heat for EVA hot melt edge banding glue in the manual adjustment gluing unit.
• Roller material — Hardened steel gluing roller with 0.8mm X texture holds its shape against daily edge contact and sawdust in the glue pot.
• Adhesive match — Working adhesive is EVA hot melt edge banding glue, so buyers should confirm their current glue type before fitting the tank.
• Customisation option — Customization is supported for buyers whose mounting pattern or wiring port differs from the standard manual adjustment gluing unit.

What changes on the shop floor when the right part goes back in:

• Restores even glue coating. The 0.8mm X anti-sawdust texture shaft clears sawdust from the roller face, which reduces streaky edge coating and glue accumulation during EVA hot melt runs on the edge bander.
• Temperature faults traced to the probe. A PT100 high-precision thermal probe and 1.5KW heating core replace the old sensing and heating set, so glue temperature faults are addressed at the source rather than worked around.
• Leak-prone tanks get a solid replacement. An anti-rust cast alloy tank replaces a corroded or leaking old pot, cutting the glue drips and residue buildup that cause downtime and rejected panel edges.
• Knob adjustment stays manual. Manual adjustment knobs let the operator set glue roller position by hand, so setup after a tank change needs no powered adjustment tools on the machine.
• Roller wear is predictable. A hardened steel gluing roller with 0.8mm X texture resists daily edge contact, giving buyers a known wear point to check instead of guessing at roller condition.
• Fit checked before the order. Matching the 80 × 68 × 14.4 mm envelope and manual adjustment layout to the old tank confirms the gluing unit before purchase, avoiding a return on a wrong-fit part.

Confirm by matching the 80 × 68 × 14.4 mm tank size and the manual adjustment knob layout to your old unit. It is a manual adjustment gluing unit for Homag edge banding machines; send a photo of your existing tank and wiring port to check.

It runs EVA hot melt edge banding glue. The 1.5KW heating core and PT100 probe are set up for that adhesive, so check your current glue type before fitting.

The gluing roller has a 0.8mm X anti-sawdust texture shaft. That texture pushes sawdust aside instead of packing it into the glue film, which helps keep the coating even.

A PT100 high-precision thermal probe reads the glue temperature, and the standard 1.5KW industrial heating core supplies the heat. Check the probe wiring port against your old unit before installation.

The tank is anti-rust cast alloy, and the gluing roller is hardened steel. Both materials are chosen for daily contact with EVA hot melt glue and sawdust.

Customization is supported. Send your machine model, the 80 × 68 × 14.4 mm dimensions of your old tank, and a photo of the mounting and wiring port so the manual glue tank can be matched.

Send the machine model, the 80 × 68 × 14.4 mm tank dimensions, and photos of the wiring port and manual adjustment knobs. That lets the supplier confirm the gluing unit before you order.

It is a manual adjustment gluing unit. The operator sets glue roller position with the manual knobs, so no powered adjustment is needed after installation.