Rubber Roller Track Woodworking Machinery Parts ART-R1 Aluminum Frame Orange

A rubber roller track for edgebanding machines, built on an aluminum frame with orange rubber rollers. It supports and guides panels during feeding and transfer. The track length is customized to your machine layout. Material is aluminum profile plus rubber roller. To confirm fit, measure the mounting area and send the required length and roller spacing; the ART-R1 model number identifies this track.

When panels drift or scratch on the outfeed, the cause is often unsupported board travel. A roller track under the panel keeps the board level and moving straight. Without it, edges chip and operators fight the machine.

The ART-R1 is an aluminum profile track fitted with orange rubber rollers. It mounts beside or after an edgebanding machine to carry panels. Length is customized to your line. Confirm fit by sending the distance between mounting points and the panel width you run.

Check that the track sits level with the machine bed and that rollers turn freely. Rubber rollers grip the panel without marking it. The aluminum frame stays straight under load. Mounting height and roller spacing determine how smoothly panels transfer.

Tracks ship in a plywood box or on a pallet. Length is customized, so specify the overall length you need. With your enquiry, send the machine model, required track length, and panel sizes you handle. That lets us match the track to your setup. Supply comes from the same range as the rest of the catalogue. Send the machine model with the enquiry so the fit is checked before dispatch. The model number and the dimensions together identify the part.

What the specification fixes, and what it leaves to the machine:

• Panel support during edgebanding — Aluminum profile frame with rubber rollers supports panels as they leave the edgebanding machine, reducing sag and misalignment.
• Roller grip on panel surfaces — Orange rubber rollers grip the panel surface to limit slippage while allowing smooth rolling movement during transfer.
• Frame material behaviour — Aluminum profile keeps the track light enough to handle and resists rust, so it holds up in workshop conditions.
• Custom length fit — Length is customized to your machine layout, so the track spans the support area you need without cutting.
• Roller contact and panel finish — Rubber roller contact prevents metal-to-panel rubbing, which helps avoid surface scratches on finished boards.
• Mounting beside the machine — Install the track level with the machine bed so panels transfer without a step that causes edge chipping.
• Roller spacing check — Check roller spacing against the panel sizes you run; closer spacing supports thinner or shorter panels better.
• Packing for transport — Plywood box or pallet packing protects the aluminum frame and rubber rollers during shipping and storage.
• Spare part identification — Model number ART-R1 identifies this track for reordering or matching with existing edgebanding machine setups.

What changes on the shop floor when the right part goes back in:

• Fewer edge chips. Supporting panels on rubber rollers reduces the chance of edge damage when boards leave the edgebanding machine, so more pieces pass inspection.
• Straighter panel travel. A level aluminum track keeps panels moving in line, which cuts the time operators spend steering boards by hand.
• Less surface scratching. Rubber rollers contact the panel instead of bare metal, which helps protect finished faces during transfer and temporary storage.
• Handles long panels. Customized length means the track can span the full support area, so long boards do not sag at the outfeed.
• Light but stiff frame. Aluminum profile is easy to position and stays straight under load, making installation and adjustment simpler for one person.
• Simple maintenance. Rust-resistant aluminum and rubber rollers need only a check that rollers turn freely, keeping downtime low.
• Flexible placement. Use the track beside the edgebander or as part of a flow rack for temporary storage, adapting to your shop layout.
• It fits the machine you already run. The ART-R1 is made for Woodworking Edgebanding Machine, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Fit depends on your machine layout and the length you order. Send the distance between mounting points and the panel width you run so the customized track matches your setup.

Length is customized, so measure the support area you need and specify it in your enquiry. Include the machine model so we can confirm the track suits your line.

The rollers are rubber with an orange color. They grip the panel and help prevent slippage while allowing smooth rolling movement.

Yes, the track can be installed beside the edgebanding machine or used as part of a flow rack for temporary storage and movement of panels.

Packing is in a plywood box or on a pallet. This protects the aluminum frame and rubber rollers during transport.

Send the machine model, the required track length, and the panel sizes you handle. That information lets us match the customized track to your production.

The frame is aluminum profile, which resists rust. It is also lightweight, making the track easier to handle and install.

Yes, ART-R1 identifies this specific rubber roller track. Use it when reordering or checking compatibility with your existing setup.