3-016-19-2680 3016192680 Aluminium Cap For Edge Bander Glue Shaft

Product Description

The 3-016-19-2680 3016192680 aluminium cap sits at the top end of the glue application shaft on Homag KAL, KFL and Ambition edge banders. It is made of aluminium and carries part number 3-016-19-2680 3016192680. Before ordering, confirm your machine model and that the existing cap matches this part number and the glue shaft top-end position.

When the glue shaft cap wears or strips, glue can escape or the shaft end can sit unevenly, causing inconsistent glue beads and edge quality problems. This cap addresses that failure point directly on Homag KAL, KFL and Ambition edge banders.

It is an aluminium cap for the top end of the glue application shaft. The part number is 3-016-19-2680 3016192680. To confirm fit, check your machine model and that the cap location matches the top end of the glue shaft.

Remove the old cap and check the shaft end for glue buildup or damage before fitting the new one. A clean, correct seat keeps the glue application shaft running as intended and helps maintain a steady glue supply.

SHUNHONGYU supplies various woodworking machine parts. Shipment is by DHL, FedEx, UPS, etc. When enquiring, send the part number 3-016-19-2680 3016192680, your machine model, and a photo of the old cap. Supply comes from the same range as the rest of the catalogue. Send the machine model with the enquiry so the fit is checked before dispatch. The model number and the dimensions together identify the part. The part is supplied as a single replacement unit. Repeat orders are quoted against the same reference.

Product Features

What the specification fixes, and what it leaves to the machine:

• Glue shaft top-end fit — The aluminium cap is located at the top end of the glue application shaft on the edge bander.
• Homag machine compatibility — Fits Homag KAL, KFL and Ambition edge banders as a spare part for the glue shaft.
• Aluminium construction — Made from aluminium, the cap is a lightweight part for the glue application shaft end.
• Part number identification — The part number 3-016-19-2680 3016192680 is marked for identification when reordering.
• Glue containment role — The cap sits at the shaft top end, where it helps keep the glue application area covered.
• Wear point access — The cap is a removable part at the shaft end, so it can be inspected during maintenance.
• Installation check — Before fitting, check the shaft end for glue residue or damage that could affect the cap seat.
• Spare parts category — Supplied as a woodworking machinery spare part for edge banding equipment maintenance.
• Shipment options — Shipment by DHL, FedEx, UPS, etc., is available for this aluminium cap.
• Model confirmation — Confirm your edge bander model is Homag KAL, KFL or Ambition before ordering this cap.
• Material — aluminium, specified for this position on edge banding machines.

Product Parameters

Product Advantages

What changes on the shop floor when the right part goes back in:

• Targets a known wear point. Replacing the cap at the glue shaft top end addresses wear or damage at that specific location, helping restore normal glue application on the edge bander.
• Matches Homag machine models. The cap is intended for Homag KAL, KFL and Ambition edge banders, so buyers with those models can check fit against a known application.
• Lightweight aluminium part. Aluminium construction keeps the cap light for handling during maintenance, without adding unnecessary weight to the glue shaft end.
• Simple identification. The part number 3-016-19-2680 3016192680 helps buyers confirm they are ordering the correct cap for their machine.
• Clear location on machine. Knowing the cap sits at the top end of the glue application shaft helps fitters locate and inspect it during service.
• Maintenance-friendly design. As a separate cap at the shaft end, it can be removed for inspection and replaced when worn, supporting regular machine upkeep.
• Shipping choice. Shipment by DHL, FedEx, UPS, etc. gives buyers options for receiving this spare part through common carriers.
• It fits the machine you already run. The aluminium cap is made for edge banding machines, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Frequently Asked Questions

Will this cap fit my Homag edge bander?

Check that your machine is a Homag KAL, KFL or Ambition model and that the cap location matches the top end of the glue application shaft.

What is the part number for this cap?

The part number is 3-016-19-2680 3016192680, which you can use to confirm the cap when ordering.

Where does this cap go on the machine?

It is located at the top end of the glue application shaft of the edge bander.

What material is the cap made from?

The cap is made of aluminium.

How do I confirm the fit before ordering?

Compare your old cap with the part number 3-016-19-2680 3016192680 and check that your machine is a Homag KAL, KFL or Ambition model.

What should I send with my enquiry?

Send the part number 3-016-19-2680 3016192680, your machine model, and a photo of the old cap to help confirm the correct part.

How is the cap shipped?

Shipment is by DHL, FedEx, UPS, etc., depending on the carrier arrangement for your order.

Can I order other woodworking machine parts?

SHUNHONGYU supplies various woodworking machine parts; contact us with your requirements for other spare parts.