3-003-04-4840 Glue Roller 3003044840 Spacer 25x30x20 Spares for Homag Machine

The 3-003-04-4840 Spacer is a 25x30x20mm replacement spacer for the glue roller assembly on Homag woodworking machines. It is new and ships via DHL, FedEx, or UPS. Before ordering, confirm that your glue roller assembly uses a spacer with 25mm inner diameter, 30mm outer diameter, and 20mm thickness, and that your machine accepts part number 3-003-04-4840 or 3003044840.

When the spacer in a Homag glue roller assembly wears or seats wrong, the roller can shift out of alignment. That leads to uneven glue spread, glue line variations, and parts that need rework. Replacing the spacer restores the correct spacing between roller components and keeps glue application consistent.

The 3-003-04-4840 Spacer is a new woodworking machine part sized 25x30x20mm. It fits Homag glue roller assemblies that use this part number. To confirm fit, check your machine's parts manual for 3-003-04-4840 or 3003044840, or measure the existing spacer's inner diameter, outer diameter, and thickness against 25x30x20mm.

Inspect the spacer seat and the roller shaft for wear or glue buildup before installation. A clean seat lets the 25x30x20mm spacer sit flat and maintain the correct gap between roller components. In use, that keeps the glue roller turning true and reduces vibration that can affect glue application.

Spacers ship by DHL, FedEx, UPS, or other carriers. No customisation or special packaging is specified. When enquiring, send the part number 3-003-04-4840 or 3003044840, the 25x30x20mm size, and a photo of the existing spacer or the machine's parts page so the fit can be checked. Supply comes from the same range as the rest of the catalogue.

What the specification fixes, and what it leaves to the machine:

• Roller alignment — This spacer maintains the correct spacing between glue roller components, which helps keep the roller aligned during operation and supports even glue application.
• Fit check — Confirm the existing spacer measures 25x30x20mm, or check the machine parts manual for 3-003-04-4840 or 3003044840 before ordering.
• Wear point — The spacer sits in the glue roller assembly and can wear or pick up glue buildup, so inspect it during routine maintenance.
• Installation detail — Clean the spacer seat and roller shaft before fitting the new 25x30x20mm spacer so it sits flat and holds the correct gap.
• Material behaviour — The spacer is a new part; its resistance to wear depends on the material grade, which is not specified beyond the 25x30x20mm size.
• Machine compatibility — This spacer fits Homag glue roller assemblies that use part number 3-003-04-4840 or 3003044840, as indicated by the part number.
• Replacement decision — Replace the spacer when the glue roller shows misalignment or uneven glue spread and the existing spacer measures 25x30x20mm.
• Spare parts stocking — Keep a spare 3-003-04-4840 spacer on hand to reduce downtime when the existing spacer wears or is damaged.

What changes on the shop floor when the right part goes back in:

• Restores roller alignment. A worn spacer lets the glue roller shift, causing uneven glue lines. Fitting a new 25x30x20mm spacer brings the assembly back to its intended spacing.
• Cuts rework from glue variation. When the roller stays aligned, glue spread stays consistent, so fewer panels need rework and material waste drops.
• Simple fit check. Measuring the old spacer against 25x30x20mm or checking for 3-003-04-4840 in the parts manual confirms fit before you order.
• Keeps a spare within reach. Storing a spare 3-003-04-4840 spacer means a worn or damaged spacer does not stall the machine while you wait for delivery.
• Clear part identification. The part number 3-003-04-4840 and alternate 3003044840 make it straightforward to match the spacer to your Homag machine documentation.
• Flexible shipping. DHL, FedEx, UPS, and other carriers are available, so you can pick a shipment method that suits your timeline.
• New condition. The spacer is new, so it arrives ready to install without the uncertainty of used parts.
• It fits the machine you already run. The spacer is made for woodworking machines, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Check your machine's parts manual for part number 3-003-04-4840 or 3003044840, or measure the existing spacer to confirm it is 25x30x20mm.

They are the spacer's inner diameter, outer diameter, and thickness in millimetres; verify each dimension against your existing spacer.

It is new. The spacer is supplied in new condition, ready for installation in a Homag glue roller assembly.

No custom sizes are specified; the spacer is supplied in 25x30x20mm. For other sizes, contact us with your requirements.

Shipment is by DHL, FedEx, UPS, or other carriers. Choose the method that best suits your delivery needs when ordering.

Send the part number 3-003-04-4840 or 3003044840, the 25x30x20mm size, and a photo of the existing spacer or parts page.

Replace it when the glue roller shows misalignment or uneven glue spread and the existing spacer measures 25x30x20mm.

Yes, we supply various woodworking machine parts. Contact us with the part numbers you need for a quote.