4-008-41-0227 4008410227 HEATING CARTRIDGE D 12.5 L 205 Glue Pot Heating Tube

A 12.5 mm diameter, 205 mm long heating cartridge for the glue pot of Homag edgebanding machines. It melts the adhesive so the roller can apply a consistent glue line. The 4-008-41-0227 4008410227 element drops into the glue pot heating tube. Before ordering, pull the old cartridge and measure its diameter and length; confirm both match 12.5 mm and 205 mm. Customization is supported. Send the part number and machine details with your enquiry.

When the glue pot stops holding temperature, the edgebander lays a cold or patchy glue line and edges fail to bond. Replacing the heating cartridge restores heat to the glue pot so adhesive melts and flows again. This 4-008-41-0227 4008410227 element is the part that does that job on a Homag edgebanding machine.

It is a heating cartridge, also called a glue pot heating tube, with a 12.5 mm diameter and 205 mm length. The element sits in the glue pot heating tube of a Homag edgebanding machine and melts the adhesive. To confirm fit, remove the old cartridge and measure its diameter and length; both must match 12.5 mm and 205 mm.

Check the bore of the glue pot heating tube for glue buildup or scoring before you fit the new cartridge. A clean 12.5 mm bore lets the 205 mm cartridge seat fully, so heat transfers to the glue pot wall. If the old cartridge was tight or loose, measure the bore as well as the cartridge.

Customization is supported. Tell us the part number 4-008-41-0227 4008410227 and the machine model when you enquire. SHUNHONGYU supplies various woodworking machine parts; contact us now with your requirements. Send the old cartridge dimensions and a photo of the glue pot if you are unsure of fitment.

What the specification fixes, and what it leaves to the machine:

• Glue pot heat source — The cartridge sits in the glue pot heating tube and melts adhesive for the edgebanding glue roller on Homag machines.
• Diameter fit check — A 12.5 mm diameter matches the glue pot heating tube bore; measure the old cartridge to confirm the bore size.
• Length fit check — The 205 mm length sets how far the cartridge reaches into the glue pot; confirm against the old part before ordering.
• Homag compatibility — Fits Homag edgebanding machines as a glue pot heating tube; check your machine model against the part number.
• Part number match — 4-008-41-0227 4008410227 identifies the exact heating cartridge; quote it when comparing against the old element.
• Glue melting function — Heat from the cartridge melts glue in the pot so the roller applies a consistent line to the panel edge.
• Wear point — The cartridge is a wear item; a failed element leaves glue cold and the edgebander unable to run production.
• Installation check — Clean the 12.5 mm bore before fitting; glue residue can stop the 205 mm cartridge from seating fully.
• Customization option — Customization is supported, so buyers can request changes to the heating cartridge to suit their glue pot setup.

What changes on the shop floor when the right part goes back in:

• Restores glue pot heat. A failed cartridge stops the glue pot from melting adhesive; fitting the 4-008-41-0227 4008410227 element brings heat back to the pot.
• Direct fit on Homag. The 12.5 mm diameter and 205 mm length match the glue pot heating tube on Homag edgebanding machines, so no adapter is needed.
• Simple fitment check. Measure the old cartridge diameter and length; if both read 12.5 mm and 205 mm, the replacement matches the tube.
• Keeps the glue line running. With the glue pot at temperature, the roller applies adhesive along the edge so panels bond without cold-glue rejects.
• One part number to quote. Use 4-008-41-0227 4008410227 when ordering; the number ties the heating cartridge to the Homag glue pot application.
• Customization supported. If your glue pot setup needs a change, customization is supported; send the details with your enquiry for review.
• Spares enquiry made easy. SHUNHONGYU supplies various woodworking machine parts; contact us now with the part number and machine model to check supply.
• It fits the machine you already run. The heating element is made for woodworking machines, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Check the part number and measure the old cartridge. The 4-008-41-0227 4008410227 cartridge fits Homag edgebanding machines as a glue pot heating tube; confirm your model and the old part's 12.5 mm diameter and 205 mm length.

It is 12.5 mm in diameter and 205 mm in length. Measure the old cartridge with a caliper; both dimensions must match 12.5 mm and 205 mm before you order.

Cold glue or a glue pot that will not reach melting temperature points to a failed cartridge. The cartridge is the heat source for the glue pot; if the pot stays cold while the machine is powered, replace the element and check the bore.

Yes, customization is supported. Send the part number 4-008-41-0227 4008410227, your machine model, and the dimensions you need so the request can be checked against your glue pot.

Send the part number 4-008-41-0227 4008410227, your machine model, and the old cartridge's diameter and length. A photo of the glue pot heating tube helps confirm the 12.5 mm bore and 205 mm depth.

No installation instructions are included with the cartridge. Fit it into the glue pot heating tube after cleaning the bore; measure the old part first so the 12.5 mm diameter and 205 mm length match.

The cartridge is identified by part number 4-008-41-0227 4008410227 and fits Homag edgebanding machines. Confirm the number against your machine's parts information before ordering.

Clean the glue pot heating tube bore of glue residue before fitting. A clear 12.5 mm bore lets the 205 mm cartridge seat fully so heat reaches the glue pot wall; check for scoring while the old cartridge is out.