YSC YSVF5120 Pneumatic Solenoid Valve for Nanxing 60301.00138 30505400 Valve

The YSC YSVF5120 is a pneumatic solenoid valve for Nanxing woodworking machines, matching part numbers 60301.00138 and 30505400. It operates at 1.5~9 Kgf/cm³ and is a direct replacement for the original valve. Before ordering, check that your machine's valve block carries the Nanxing 60301.00138 or 30505400 number and that your air supply falls within the 1.5~9 Kgf/cm³ range. Send a photo of the old valve and the machine model with your enquiry to confirm fit.

When a Nanxing machine's solenoid valve sticks or burns out, the air cylinder stops moving and the machine sits idle. The YSC YSVF5120 is the replacement valve for that failure, matching Nanxing part numbers 60301.00138 and 30505400. It restores pneumatic control without changing the valve block or wiring.

This is a YSC YSVF5120 air solenoid valve, a pneumatic directional valve with a working pressure range of 1.5~9 Kgf/cm³. It fits Nanxing woodworking machines that use the 60301.00138 or 30505400 valve. To confirm fit, check the part number stamped on your old valve or the machine's parts book against these two numbers.

Before installation, check that your air line pressure stays within 1.5~9 Kgf/cm³ and that the valve seat and ports are clean. Mount the valve in the same orientation as the original, with the coil accessible for future service. Correct pressure and clean air keep the valve shifting reliably through production shifts.

YSC YSVF5120 valves are available as single units; customisation is not stated. For a fast match, send the machine model, the part number from your old valve (60301.00138 or 30505400), and a photo of the valve and its connector. That lets us confirm the YSVF5120 is the correct replacement before you order.

What the specification fixes, and what it leaves to the machine:

• Direct replacement fit — Matches Nanxing part numbers 60301.00138 and 30505400, so it drops into the existing valve block without adapters.
• Pressure range for shop air — Rated for 1.5~9 Kgf/cm³, covering the air supply used on Nanxing woodworking machines without extra regulation.
• Coil service access — The coil mounts on the valve body and can be reached for inspection or replacement without removing the entire manifold.
• Seal wear point — Internal seals are the main wear item; keeping air clean and within 1.5~9 Kgf/cm³ extends seal life between replacements.
• Port orientation — Mount the valve in the same orientation as the original so air lines connect without stress or kinks.
• Pneumatic response — The valve shifts to direct air flow to cylinders, restoring the rapid response needed for clamping and positioning.
• Machine compatibility — Fits Nanxing woodworking machines that use the 60301.00138 or 30505400 valve, as shown on the old part.
• Single-unit supply — Order one valve at a time; packing and customisation details are not stated, so confirm with your enquiry.
• Fit check method — Compare the part number on your old valve to 60301.00138 or 30505400 before ordering.

What changes on the shop floor when the right part goes back in:

• Restores machine uptime. A failed solenoid valve stops the machine; replacing it with the YSVF5120 gets the pneumatic circuit working again without waiting for a full valve block.
• Matches two Nanxing part numbers. Because it covers 60301.00138 and 30505400, you can replace either valve with one part number and reduce the spares you need to stock.
• Works within common shop pressure. The 1.5~9 Kgf/cm³ range means the valve operates on the air supply already set for Nanxing machines, so no extra regulator is needed.
• Simple fit confirmation. Check the number on your old valve against 60301.00138 or 30505400; if it matches, the YSVF5120 is the correct replacement.
• Easy coil access. The coil can be reached for inspection without removing the valve body, cutting the time needed for routine checks.
• Fewer wrong orders. Send a photo of the old valve and machine model with your enquiry, and we confirm the YSVF5120 before you commit to the order.
• Clear pressure limit. Knowing the valve is rated for 1.5~9 Kgf/cm³ helps you spot air supply problems that could shorten valve life.
• It fits the machine you already run. The YSVF5120 is made for woodworking machines, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Check the part number on your old valve: if it reads 60301.00138 or 30505400, the YSVF5120 is the replacement. Also confirm your machine model with a photo of the valve.

It operates at 1.5~9 Kgf/cm³. Set your air supply within that range; higher pressure can damage the seals and cause leaks.

It is the complete YSC YSVF5120 air solenoid valve, not just a coil. You receive the valve body and coil as one unit.

Mount it in the same orientation as the original, connect the air lines and coil plug, and check for leaks before running the machine.

It is intended for Nanxing machines that use the 60301.00138 or 30505400 valve. For other machines, confirm the port size and pressure range first.

Send the machine model, the part number from your old valve (60301.00138 or 30505400), and a clear photo of the valve and connector.

Customisation and packing details are not stated. Tell us what you need and we will confirm what is possible for your order.

If your old valve does not show 60301.00138 or 30505400, send a photo and the machine model so we can check whether the YSVF5120 still fits.