3007181320 Roll 3-007-18-1320 Homag Steel Pressure Roller D 18 L 40 Homag Spares

A Homag steel pressure roller, part number 3-007-18-1320 / 3007181320, measuring 18mm in diameter and 40mm in length. It fits Homag woodworking machines. The steel body takes pressure at the contact point and wears over time. Check your machine's parts book for this number before ordering. Measure the old roller's diameter and length to confirm 18mm and 40mm. Send the part number and a photo of the worn roller with your enquiry.

When a pressure roller wears, it loses its true diameter and the pressure point shifts. Boards can slip, feed unevenly, or mark at the roller contact. This roller restores the original 18mm diameter and 40mm length so the pressure line sits where the machine expects it.

This is a Homag pressure roll, steel, with an 18mm diameter and 40mm length. It fits Homag woodworking machines. To confirm fit, look up 3-007-18-1320 or 3007181320 in your machine's parts book, then measure the old roller: 18mm across and 40mm long means this is the one.

Pull the old roller and check the bore and mounting arrangement on your machine before ordering. The 18mm diameter and 40mm length must match the space and the shaft it runs on. If the old roller is worn below 18mm, the new one will bring the pressure back to spec.

Supply is straightforward: this is a single spare part, not a kit. Send the part number 3-007-18-1320 or 3007181320, the machine model, and a photo of the old roller with your enquiry. That lets the supplier check the roller against your machine before shipping. Supply comes from the same range as the rest of the catalogue.

What the specification fixes, and what it leaves to the machine:

• Wear point — The 18mm diameter is the contact surface that wears; measure yours to see if it has dropped below this size.
• Fit check by length — A 40mm overall length sets where the roller sits on the shaft; compare it to the old part before fitting.
• Steel body behaviour — Steel construction resists compression at the pressure point, so the roller holds its shape under load.
• Machine match — This roller fits Homag woodworking machines; confirm your model against the part number in the parts book.
• Part number lookup — Use 3-007-18-1320 or 3007181320 when searching a parts book or asking for a replacement.
• Installation reference — The roller mounts on the machine's existing shaft; check the bore and retaining method on your unit.
• Replacement trigger — Replace when the roller no longer measures 18mm or when board feed becomes uneven at the pressure point.
• Spare parts category — This is a woodworking machine spare part, so it is ordered as a single replacement component.
• Diameter control — An 18mm diameter keeps the pressure line consistent; a worn roller changes that line and affects feed.
• Length control — The 40mm length positions the roller correctly on the shaft; a mismatch can cause misalignment.

What changes on the shop floor when the right part goes back in:

• Restores the pressure line. A new 18mm diameter roller puts the contact point back where the machine was set up for it, so boards feed as they did before wear.
• Easy to identify. The part number 3-007-18-1320 and the alternate 3007181320 give you two references to match against your machine's parts book.
• Steel holds its size. Steel resists flattening at the pressure point, so the 18mm diameter stays closer to spec than a softer roller would.
• Simple fit check. Measuring the old roller for 18mm diameter and 40mm length takes a caliper and a minute, and confirms the fit before you order.
• One part, not a kit. You order the roller you need, which keeps the spare parts shelf simple and avoids buying parts you will not use.
• Clear wear signal. When the old roller measures under 18mm, you know it is worn; that gives you a measurable replacement trigger.
• Homag machine fit. The roller is made for Homag woodworking machines, so it matches the mounting arrangement already on your equipment.
• It fits the machine you already run. The pressure roll is made for woodworking machines, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Check your machine's parts book for 3-007-18-1320 or 3007181320 and measure the old roller for 18mm diameter and 40mm length.

It is 18mm in diameter and 40mm in length, and both dimensions need to match the old part for correct fit.

Yes, it is a steel pressure roller, which is why it resists compression at the contact point.

Replace it when the old roller measures under 18mm or when board feed becomes uneven at the pressure point.

Send the part number 3-007-18-1320 or 3007181320, your machine model, and a photo of the old roller.

No, it is a single spare part; you order the roller on its own.

It fits Homag woodworking machines, but confirm your model against the part number in the parts book before ordering.

The Homag number is 3-007-18-1320, and 3007181320 is the alternate reference for the same roller.