4-060-18-0081 Chain Pad For Homag Edgebander 4060180081 Edging Machine Track Pad

The 4-060-18-0081 chain pad is a track pad for Homag edgebanders, used in the conveyor chain to support workpieces. It measures 126mm long, 69mm wide, and 47mm high, and is made from PA 6 with a 55 Shore hardness. The part number 4060180081 also identifies it. To confirm fit, check your machine's parts manual for this number and compare the old pad's dimensions and material marking.

When the chain pads on a Homag edgebander wear, workpieces can sit unevenly and shift as they travel through the edging station. A worn pad may no longer hold the 47mm height, causing inconsistent support along the track. Replacing pads at the first sign of wear keeps the conveyor chain running true.

This chain pad is a spare part for the conveyor track of Homag edgebanding machines. It is made from PA 6 with a 55 Shore hardness and measures 126mm in length, 69mm in width, and 47mm in height. The part number is 4-060-18-0081, also written 4060180081. To confirm fit, match this number in your machine's parts list and check the old pad's dimensions.

Before fitting, check the chain for stretch and the track for buildup that could stop the pad seating flat. The pad mounts on the chain and carries the workpiece past the glue and pressure sections, so a pad that sits proud or loose will affect how the panel runs. Clean the mounting point and seat the new pad fully.

Orders are supplied as individual chain pads from China. No customisation or packaging details are specified, so confirm these with the supplier. When enquiring, send the part number 4-060-18-0081 or 4060180081, the quantity you need, and a photo of the old pad with its dimensions so the supplier can check the match.

What the specification fixes, and what it leaves to the machine:

• Track support point — The pad sits in the conveyor chain track and provides the surface the workpiece rests on as it moves through the edgebander.
• Length reference — At 126mm long, the pad covers a set span of the chain run and can be checked against the old pad with a tape measure.
• Width reference — The 69mm width matches the track channel and helps confirm the pad sits correctly without overhang or side play.
• Height reference — A 47mm height sets the pad's profile in the chain, so a worn pad can be compared directly to this figure.
• Material identification — The pad is made from PA 6 with a 55 Shore hardness, a combination that gives a firm, wear-resistant contact surface.
• Wear check point — Inspect the top face for flattening or grooving; a pad that no longer holds its shape should be replaced.
• Mounting location — The pad mounts on the conveyor chain, and a clean, undamaged chain link helps the pad seat flat and stay in position.
• Fit confirmation — Use the part number 4-060-18-0081 or 4060180081 in the machine's parts list to confirm the pad before ordering.

What changes on the shop floor when the right part goes back in:

• Keeps workpiece support consistent. A pad at the full 47mm height supports the panel evenly along the track, which helps avoid tipping or catching as the workpiece passes the edging station.
• Simplifies replacement checks. The 126mm length and 69mm width can be measured against the old pad on the bench, so you can confirm the match before fitting.
• Firm contact surface. PA 6 with 55 Shore hardness gives the pad a firm face that resists flattening under the workpiece, helping maintain a stable running surface over time.
• Reduces guesswork on part numbers. The pad is identified by 4-060-18-0081 and 4060180081, so you can cross-check the number in your parts manual before ordering.
• Fits the conveyor track. Designed for the chain track on Homag edgebanders, the pad seats in the chain and carries the workpiece through the machine's edging path.
• Easy to inspect for wear. The pad's top face is visible during routine checks; look for grooving or a worn profile and replace the pad when it no longer sits flat.
• Clear enquiry process. Sending the part number, quantity, and a photo of the old pad with its dimensions helps the supplier check the match before you commit to an order.

Check your machine's parts manual for the number 4-060-18-0081 or 4060180081. Also measure the old pad: it should be 126mm long, 69mm wide, and 47mm high, and marked with the material reference 55SHORE PA 6.

The pad is 126mm in length, 69mm in width, and 47mm in height. These figures match the size given for this part, so compare them to your old pad before ordering.

The material reference is 55SHORE PA 6. PA 6 is a polyamide, and the 55 Shore hardness indicates the pad's firmness; check the old pad for a matching marking.

It mounts on the conveyor chain track of the edgebander. The pad supports the workpiece as the chain carries it through the edging process, so fit it in the same position as the old pad.

Yes, pads can be replaced individually. Check the surrounding pads for wear at the same time, since uneven wear across the chain can affect how the workpiece runs.

Check the chain link for damage and clean any glue or chip buildup from the mounting area. A clean, flat seat helps the new pad sit at the correct 47mm height.

Send the part number 4-060-18-0081 or 4060180081, the quantity you need, and a photo of the old pad with its dimensions. Ask the supplier to confirm the match and any packing details.

No customisation or packaging details are specified for this pad. Confirm both with the supplier when you enquire, along with the quantity and part number.