4-008-61-1536 4008611536 Photoelectric Sensor SICK WLG4SC-3P3232B01 For Homag

A SICK WLG4SC-3P3232B01 photoelectric sensor, Homag part number 4-008-61-1536 or 4008611536, fits Homag woodworking machines. It measures 12.2 mm x 41.8 mm x 17.3 mm and runs on 10...30V DC. Buyers confirm fit by matching the Homag part number and model number on the machine's parts list or the old sensor label. The rectangular housing mounts where the original sensor sits.

When a Homag machine stops indexing or misreads a panel edge, the photoelectric sensor is often the first suspect. A failed sensor at 4-008-61-1536 or 4008611536 stops the control from seeing the workpiece, so the cycle halts or the wrong cut is made.

The SICK WLG4SC-3P3232B01 is a rectangular photoelectric sensor measuring 12.2 mm x 41.8 mm x 17.3 mm. It is a direct replacement for Homag part 4-008-61-1536 or 4008611536. Confirm the fit by matching both numbers on the machine's parts list or the label on the old sensor.

Check the mounting bracket and the sensing window before fitting. The 12.2 mm width and 17.3 mm depth must clear the bracket, and the 10...30V DC supply must match the machine's control voltage. A correct fit keeps the sensor aligned with the reflector or target.

Supply is straightforward: the sensor ships as a single unit. No customisation or special packaging is offered. Send the Homag part number 4-008-61-1536 or 4008611536, the SICK model WLG4SC-3P3232B01, and the machine model with your enquiry so the correct part is picked. Supply comes from the same range as the rest of the catalogue. Send the machine model with the enquiry so the fit is checked before dispatch.

What the specification fixes, and what it leaves to the machine:

• Machine stop detection — Fits Homag machines as a photoelectric sensor for part 4-008-61-1536 or 4008611536, restoring the control's view of the workpiece.
• Housing size check — Measures 12.2 mm x 41.8 mm x 17.3 mm, so the rectangular body fits the original bracket space without modification.
• Voltage match — Runs on 10...30V DC, matching the control voltage range used on Homag woodworking machines for this sensor circuit.
• Model identification — The SICK WLG4SC-3P3232B01 model number on the label lets a buyer confirm the exact sensor before ordering.
• Mounting position — Rectangular housing mounts in the same orientation as the original, keeping the sensing face aligned with the target.
• Wear point — The sensing window is the wear point; check it for dust or scratches during routine machine maintenance.
• Replacement fit — Direct replacement for Homag 4-008-61-1536 or 4008611536, so no rewiring or bracket changes are needed.
• Connection check — Confirm the 10...30V DC supply at the machine connector before fitting the new sensor to avoid a repeat failure.
• Alignment setting — After mounting, align the sensor with the reflector or target using the machine's normal setup procedure.
• Single-unit supply — Each order supplies one photoelectric sensor; no custom packaging or modifications are offered for this part.

What changes on the shop floor when the right part goes back in:

• Restores machine cycle. A working sensor at 4-008-61-1536 or 4008611536 lets the control see the workpiece again, so the Homag machine resumes its normal cycle without false stops.
• Fits the original bracket. The 12.2 mm x 41.8 mm x 17.3 mm rectangular housing matches the original mounting space, so the fitter avoids drilling or adapting the bracket.
• Correct voltage range. The 10...30V DC range matches the machine's control supply, so the sensor works with the existing wiring and no voltage adapter is needed.
• Clear part matching. Both the Homag number 4-008-61-1536 or 4008611536 and the SICK model WLG4SC-3P3232B01 are marked, so the buyer can check the old label against the new unit.
• Simple stock decision. Knowing the sensor is a single unit with no custom options lets the buyer order the exact quantity needed for the repair.
• Reduced diagnosis time. Matching the model and part numbers before ordering removes guesswork, so the maintenance team spends less time identifying the failed sensor.
• Repeatable setup. The rectangular housing mounts in the same position as the original, so the sensing alignment can be restored using the machine's standard setup.

Match the Homag part number 4-008-61-1536 or 4008611536 and the SICK model WLG4SC-3P3232B01 on your machine's parts list or the old sensor label.

It runs on 10...30V DC, so check that your machine's control supply for this sensor circuit falls within that range.

The rectangular housing measures 12.2 mm x 41.8 mm x 17.3 mm, so compare that with the space on your mounting bracket.

Yes, it is supplied as the replacement for Homag 4-008-61-1536 or 4008611536 and uses the SICK WLG4SC-3P3232B01 model.

Check the 10...30V DC supply at the connector and inspect the bracket and sensing window for damage or misalignment before mounting.

No customisation or special packaging is offered; the sensor is supplied as a single unit with the part numbers shown.

Send the Homag part number 4-008-61-1536 or 4008611536, the SICK model WLG4SC-3P3232B01, and your machine model so the correct sensor is picked.

Mount it in the original bracket position and align the sensing face with the reflector or target using the machine's normal setup procedure.