3805020100 3-805-02-0100 Lining Pad Clamping Collet Cover LINING 176MM X 23MM

The 3805020100 (3-805-02-0100) Lining Pad Clamping Collet Cover fits the Weeke BHX500 and measures 176MM X 23MM. It is a woodworking machine spare part that sits in the clamping collet area, and a worn one will show up as poor clamping on the BHX500. Check the old pad against 176MM X 23MM before ordering, and confirm the part number on the machine. Both 3805020100 and 3-805-02-0100 identify the same pad, so either number can be used to match it.

When the lining pad on a Weeke BHX500 wears or tears, the clamping collet no longer holds work the way it should. The pad takes the contact, so a flattened or split lining shows up as slipping or inconsistent seating at the clamp. Replacing it restores the contact face the collet works against.

This is a lining pad, also called a clamping collet cover, sized 176MM X 23MM. It is a woodworking machine spare part made for the Weeke BHX500. To confirm the fit, pull the old pad and measure it against 176MM X 23MM, then check the part number on the machine: 3805020100 and 3-805-02-0100 both identify this pad.

Before fitting, inspect the collet seat for burrs or old adhesive left behind, because anything under the new pad changes how it sits. The pad mounts over the collet cover area and must lie flat across its 176MM X 23MM face. A flat seat means the clamp contacts evenly instead of pinching at one point.

Packing and customisation are not specified here; ask when you enquire. SHUNHONGYU can supply various Homag parts. Send the part number 3805020100 or 3-805-02-0100, the machine model Weeke BHX500, and a photo or measurement of the old pad at 176MM X 23MM so the match is checked before dispatch.

What the specification fixes, and what it leaves to the machine:

• Wear contact face — The lining takes the contact in the clamping collet area, so a worn pad is the first thing to check when clamping slips.
• Weeke BHX500 fit — Sized for the Weeke BHX500, this clamping collet cover keeps the pad matched to the machine instead of trimmed to fit.
• 176MM X 23MM footprint — The pad measures 176MM X 23MM, so you can compare it to the old lining with a rule before ordering.
• Two part numbers — Order by 3805020100 or 3-805-02-0100; both numbers identify the same lining pad clamping collet cover.
• Flat mounting face — The pad mounts flat across its 176MM X 23MM face, so the collet contacts evenly instead of pinching at one edge.
• Durable lining — Made from durable material, the lining pad is built to stay in service under repeated clamping on the BHX500.
• Seat preparation — Clean old adhesive and burrs from the collet seat first, because anything left under the pad changes how it sits.
• Visual wear check — A flattened or split lining is visible once the pad is off, which tells you whether the clamp problem is the pad.

What changes on the shop floor when the right part goes back in:

• Restores even clamp contact. A flat 176MM X 23MM lining lets the clamping collet bear on the work evenly, so parts seat the same way from one cycle to the next on the Weeke BHX500.
• One pad, two order numbers. You can order by 3805020100 or 3-805-02-0100, which means a number read off an old label or a manual still points to the same lining pad.
• Measure before you commit. Because the pad is 176MM X 23MM, your fitter can check the old lining with a rule in minutes and avoid ordering the wrong size.
• Fewer clamp-side faults. Replacing a worn lining takes the pad out of the list of causes when the BHX500 clamp misbehaves, so troubleshooting moves to the next item faster.
• Clean seat, stable pad. Cleaning burrs and old adhesive before mounting keeps the pad flat over its 176MM X 23MM face, which is what keeps the clamp contact consistent.
• Durable under repeat clamping. Durable material suits a wear position that sees repeated clamping, so the lining pad is built for the contact duty it carries.
• Matched to the machine. Made for the Weeke BHX500 as a woodworking machine spare part, the pad goes into the collet cover position without trimming or adaptation.

Yes, it is made for the Weeke BHX500. Measure the old pad against 176MM X 23MM and check the part number on the machine to confirm the match.

Quote either 3805020100 or 3-805-02-0100, because both numbers identify this lining pad clamping collet cover.

Measure the old lining before ordering. The pad is 176MM X 23MM, so a rule against the old part shows quickly whether it matches.

It is the lining pad, or clamping collet cover, that sits in the collet area. A worn one shows up as slipping or uneven seating at the clamp.

Check the collet seat for burrs and old adhesive. Anything left under the pad changes how the 176MM X 23MM face sits.

Yes, SHUNHONGYU can supply various Homag parts. Send the part numbers you need and they can be checked against your enquiry.

Send the part number 3805020100 or 3-805-02-0100, the machine model Weeke BHX500, and the old pad measurement at 176MM X 23MM.

Durable material is used for the lining. It is a wear part in the clamp area, so inspect it during regular machine checks.