4011010996 Screw Connector WINKEL for Homag Woodworking Machine Spare

This is a WINKEL screw connector, part number 4-011-01-0996, for Homag woodworking machines. It measures D=8 with a G1/4 thread. The connector is an original spare part and fits machines that use the WINKEL D=8 G1/4 interface. To confirm fitment, check that your machine's existing connector matches the D=8 and G1/4 markings. The part is a screw-in plug connection used in woodworking machine assembly and maintenance.

When a screw connection on a Homag machine works loose, the result is lost clamping force, air leaks, or a joint that will not hold torque. This connector is the replacement for that joint. It restores the connection without modifying the machine or the mating port.

The 4-011-01-0996 is a screw connector with a D=8 diameter and a G1/4 thread, made by WINKEL. It fits Homag woodworking machines that use this interface. Before ordering, confirm the old part carries the same D=8 and G1/4 markings and that the machine model accepts WINKEL connectors.

Check the thread in the mating port for damage before installation. The connector screws into a G1/4 port and must seat fully; a cross-thread will leak or loosen under vibration. A clean, seated joint keeps the connection stable through the machine's operating cycle.

Supply is for the connector as an original WINKEL part. No customisation or packaging options are stated. Send your machine model, the old part number 4-011-01-0996, and a photo of the existing connector and port with your enquiry so the fit can be checked before dispatch. Supply comes from the same range as the rest of the catalogue. Send the machine model with the enquiry so the fit is checked before dispatch.

What the specification fixes, and what it leaves to the machine:

• Thread size match — The connector uses a G1/4 thread, so it threads into ports machined for that standard size.
• Diameter for seating — A D=8 diameter gives the connector its seating size in the machine port.
• Original WINKEL part — Supplied as an original WINKEL connector, not a copy, for machines built around this interface.
• Screw-in installation — The screw-in plug connection design means the part installs by threading, with no press tools needed.
• Homag machine fit — Fits Homag woodworking machines that accept the WINKEL D=8 G1/4 connector interface.
• Part number check — The 4-011-01-0996 number on the old part gives a direct match to this connector.
• Vibration resistance — A fully seated G1/4 thread resists loosening better than a partly engaged connection.
• Leak control point — The thread joint is the leak control point; inspect it when air or vacuum performance drops.
• Replacement routine — Keep this connector as a spare for scheduled maintenance on Homag machines using D=8 G1/4 ports.
• Cross-reference use — The 4011010996 and 4-011-01-0996OR references help identify the same connector in parts lists.
• Specified characteristic — original.
• Direct replacement — the mounting point is unchanged, so no adapter, shim or re-machining is needed.

What changes on the shop floor when the right part goes back in:

• Direct replacement. Because the connector carries the WINKEL D=8 G1/4 designation, you replace the old part without adapters or rework on the machine port.
• Fewer machine stops. A spare 4-011-01-0996 on the shelf means a loose or damaged connector does not idle the machine while you search for a part.
• Correct thread engagement. The G1/4 thread matches the port, so the connector seats fully and holds torque through the machine cycle instead of backing out.
• Simple fit check. You confirm fit by comparing D=8 and G1/4 markings on the old connector, so ordering does not depend on guesswork about machine models.
• Original interface. Using the original WINKEL connector keeps the connection as built, so nearby components and port threads are not stressed by a mismatched part.
• Maintenance planning. With the part number 4-011-01-0996 on file, your maintenance team can add the connector to scheduled checks on Homag machines.
• Clear enquiry path. Sending the machine model and a photo of the old connector lets the supplier verify the D=8 G1/4 fit before the order ships.
• It fits the machine you already run. The screw connector is made for Woodworking Machine, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Check the old connector for D=8 and G1/4 markings; if they match, this WINKEL connector is the replacement. Also confirm the machine uses WINKEL connectors, as the part is built to that interface.

D=8 is the connector diameter and G1/4 is the thread size. Both numbers appear on the original part, so compare them directly with your old connector before ordering.

Yes, the connector is supplied as an original WINKEL part. The part number 4-011-01-0996 and the WINKEL D=8 G1/4 marking identify it.

Fit depends on whether the machine uses the WINKEL D=8 G1/4 interface. Check the old connector's markings and send your machine model with the enquiry so the fit can be confirmed.

It screws into a G1/4 port. Clean the threads, start it by hand to avoid cross-threading, and tighten until it seats fully so the joint holds under vibration.

Inspect the mating port thread for damage and confirm the old part carries the same D=8 and G1/4 markings. A damaged port will not hold a new connector securely.

Send the machine model, the old part number 4-011-01-0996, and a photo of the existing connector and port. This lets the supplier check the D=8 G1/4 fit before dispatch.

No customisation or packaging options are stated for this connector. It is supplied as the original WINKEL part; ask the supplier about current packing when you enquire.