4-010-04-0114 Homag Edgebander Power Stop 4010040114 M20x1.5m Shock Absorber

This Power Stop is a shock absorber for Homag edgebanders, including the KAL model. It carries Homag number 4010040114 / 4-010-04-0114 and a size of M20 X 1,5 / 100. The M20x1.5 thread mounts it on the machine. Before ordering, confirm your edgebander is a Homag KAL and that the old stop matches this number and thread size. Send the machine model and the part number from your manual or the old unit with your enquiry.

When the power stop on a Homag edgebander stops absorbing shock, the feed cycle can lose its smooth stop at the end of travel. The machine may shudder or the stop may fail to hold position. Replacing the worn unit restores the damped stop the cycle depends on.

This is a Power Stop shock absorber with Homag number 4010040114 / 4-010-04-0114 and size M20 X 1,5 / 100. It fits Homag KAL edgebanders. To confirm fit, check the number on the old stop or in the machine parts book, and match the M20x1.5 thread.

Check that the mounting thread is M20x1.5 and that the old stop comes off without damaged threads. A clean M20x1.5 thread lets the new unit seat fully. In use, correct seating keeps the stop aligned so the shock absorber works through its stroke.

Supply comes as the Power Stop unit with Homag number 4010040114 / 4-010-04-0114. No packing or customisation details are stated. For an enquiry, send the machine model, the old part number, and a photo of the mounting thread so the correct stop can be supplied. Supply comes from the same range as the rest of the catalogue. Send the machine model with the enquiry so the fit is checked before dispatch.

What the specification fixes, and what it leaves to the machine:

• Damped stop at end of travel — The Power Stop absorbs shock at the end of the edgebander cycle, reducing the hard stop that can shake the machine.
• Homag KAL fitment — Fits Homag KAL edgebanders, so buyers running that model can match the stop to their machine before ordering.
• M20x1.5 mounting thread — The M20x1.5 thread is the mounting interface, and checking it against the old stop confirms the unit will seat.
• Size reference M20 X 1,5 / 100 — The size M20 X 1,5 / 100 gives a direct reference to compare with the old unit or the parts book.
• Dual part number check — Homag numbers 4010040114 and 4-010-04-0114 both identify this stop, so either number on the old unit confirms it.
• Shock absorber function — As a shock absorber, the unit damps impact rather than passing it into the machine frame and the feed mechanism.
• Thread condition at installation — Inspect the M20x1.5 thread on the machine before fitting; damaged threads prevent the stop from seating fully.
• Wear point to watch — The shock absorber is a wear point; a stop that no longer damps the end of travel signals it is time to replace.

What changes on the shop floor when the right part goes back in:

• Restores the damped stop. A working shock absorber takes the impact out of the end of the feed cycle, so the edgebander stops cleanly instead of jolting the workpiece.
• One number, easy match. Because the stop carries both 4010040114 and 4-010-04-0114, the buyer can check either number on the old unit and order without guesswork.
• Thread check before dispatch. Matching the M20x1.5 thread against the machine mount before ordering avoids a stop that will not seat and a wasted machine stop.
• Fits the Homag KAL. Buyers running a Homag KAL edgebander can fit this stop directly, keeping the machine on its normal maintenance schedule.
• Simple wear replacement. Treating the stop as a wear item means it can be swapped when damping fades, before the hard stop affects the feed cycle.
• Clear size reference. The M20 X 1,5 / 100 size gives the buyer a concrete figure to compare with the old unit when the number is unreadable.
• Enquiry with the right details. Sending the machine model, old part number and a thread photo speeds up supply of the correct Power Stop.

It fits Homag KAL edgebanders. Check your machine model is KAL and confirm the old stop carries 4010040114 or 4-010-04-0114.

The thread is M20x1.5. Compare it with the old stop or the machine mount before ordering.

Look for 4010040114 or 4-010-04-0114 on the old stop or in the machine parts book. Either number identifies this Power Stop.

It is a shock absorber that damps the end of the feed cycle. A worn unit stops absorbing shock and the machine can jolt.

If the end of travel feels hard or the machine shakes at the stop, the shock absorber is no longer damping and should be replaced.

Check the M20x1.5 thread on the machine mount is clean and undamaged. A damaged thread prevents the stop from seating fully.

Send the machine model, the old part number, and a photo of the mounting thread. That lets the correct Power Stop be supplied.

Yes, it is supplied as the Power Stop unit with Homag number 4010040114 / 4-010-04-0114. No packing details are stated.