123x52x27mm Edgebanding Machine Press Bracket - Woodworking Machine Spare Part

A press bracket for edgebanding machines, model PSW078, sized φ123xφ52x27mm and made from plastic and metal in black. It mounts on the machine's press section to hold the pressure roller assembly. Confirm fitment by measuring the old bracket's outer diameter, bore, and thickness, and by checking the mounting hole pattern. The bracket is a spare part for woodworking machinery, not a universal fit. Order by model number and size to avoid mismatch.

When an edgebanding machine's press bracket wears or cracks, the pressure roller loses its hold and the band can lift or wander. Replacing the bracket restores the roller's position. This bracket, model PSW078, addresses that specific failure point on the press section.

The PSW078 press bracket measures φ123xφ52x27mm and is made from plastic and metal in black. It fits edgebanding machines that use this bracket size. To confirm fit, measure your existing bracket's outer diameter, bore, and thickness, and compare them to φ123xφ52x27mm.

Check the mounting holes and the bracket seat on the machine before ordering. The bracket mounts at the press roller station, and the φ123xφ52x27mm dimensions must match the seat and shaft. A correct match keeps the roller aligned and the band pressed evenly.

Supply is by model number PSW078. Packing and customisation are not stated, so confirm those with the supplier. Send your machine make and model, the old bracket's φ123xφ52x27mm measurements, and a photo of the mounting area with your enquiry. Supply comes from the same range as the rest of the catalogue. Send the machine model with the enquiry so the fit is checked before dispatch. The model number and the dimensions together identify the part.

What the specification fixes, and what it leaves to the machine:

• Press roller mounting — The bracket holds the press roller at the edgebanding machine's pressure station, keeping the roller in contact with the band.
• Size match — At φ123xφ52x27mm, the bracket matches machines that use this exact outer diameter, bore, and thickness.
• Material mix — Plastic and metal construction combines a metal load-bearing structure with plastic contact areas to suit the press action.
• Wear replacement — Replace the bracket when the original shows cracks or worn mounting holes that let the press roller move off position.
• Color identification — The black finish makes the bracket easy to identify among other spare parts during maintenance checks.
• Fitment check — Measure the old bracket's φ123xφ52x27mm dimensions and hole pattern before ordering to confirm the replacement.
• Model reference — Model number PSW078 identifies this bracket, so order by that number and the φ123xφ52x27mm size.
• Roller alignment — A correctly sized bracket keeps the press roller aligned with the band path, reducing edge lift during pressing.
• Installation access — The bracket mounts at the press station, so check clearance around the roller before removing the old bracket.
• Spare part stock — Keep a PSW078 bracket on hand as a spare for edgebanding machine maintenance to reduce press station downtime.

What changes on the shop floor when the right part goes back in:

• Restores press roller position. A worn bracket lets the roller drift, causing band lift. Fitting a φ123xφ52x27mm PSW078 bracket puts the roller back in its seat.
• Matches by size, not guesswork. The φ123xφ52x27mm dimensions give you a measurable check against the old bracket before you order.
• Plastic and metal build. The material mix suits the press station's load and contact needs, using metal for structure and plastic where the bracket meets the machine.
• Cuts diagnostic time. When band lift starts, checking the press bracket for wear is a direct step; a cracked PSW078 bracket is visible at the press station.
• Simple spare part number. Ordering by PSW078 and φ123xφ52x27mm avoids confusion with other brackets that look similar but differ in size.
• Black finish for identification. The black color helps you spot the bracket during maintenance and distinguish it from other press station parts.
• Keeps a spare within reach. Holding a PSW078 bracket in stock means a worn bracket does not stop the edgebander while you wait for a replacement.
• It fits the machine you already run. The PSW078 is made for Edgebanding Machine Spare, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Check the size first: the bracket is φ123xφ52x27mm. Measure your old bracket's outer diameter, bore, and thickness, and compare them to φ123xφ52x27mm. Also check the mounting hole pattern. If they match, the PSW078 bracket is the correct size.

It holds the press roller at the pressure station. The bracket keeps the roller in position so the band is pressed onto the panel edge. A worn bracket lets the roller move, which can cause band lift.

Plastic and metal. The bracket combines these materials to suit the press station. The color is black.

Measure the outer diameter, the bore, and the thickness. The PSW078 size is φ123xφ52x27mm. Use these three measurements to compare with your old bracket before ordering.

Order quantity is not stated. Send your required quantity with the enquiry and the supplier will confirm.

Send the machine make and model, the old bracket's φ123xφ52x27mm measurements, and a photo of the mounting area. Also include the model number PSW078 and the quantity you need.

Mounting hardware is not stated. Check with the supplier whether screws or pins are included before you order.

Packing details are not stated. Ask the supplier for the packing method and quantity per pack when you enquire.