3-601-06-0341 Fiber Glass Scraper Spring GFK L87 For Homag Machine 3601060341

The 3-601-06-0341 Fiber Glass Scraper Spring is a fiber glass scraper spring for Homag machines, sized L=87mm. It carries part number 3-601-06-0341 and the GFK L87 marking, so you can match it to the spring you are replacing. Fiber glass is the material, and the part sits in the woodworking machine spares category for Homag equipment. Before ordering, pull your old spring and compare the 87mm length and the 3-601-06-0341 number against this one. Shipment runs by FedEx, UPS or DHL.

When the scraper spring in a Homag machine loses its push, the scraper stops pressing evenly and the finish shows it. A tired spring lets the scraper ride or chatter instead of holding contact. Replacing it with the correct L=87mm spring restores the scraper's working pressure without touching the rest of the head.

This is a fiber glass scraper spring, part number 3-601-06-0341, marked GFK L87 and measuring L=87mm. It fits Homag machines as a woodworking machine spare. To confirm the fit, take the spring out of the machine and check three things against it: the 3-601-06-0341 number, the GFK L87 marking and the 87mm length.

Check the spring seat and the scraper arm before you fit the new one. Wear at the seat, a bent arm or a packed chip pocket will spoil the spring's action even when the spring is right. With a clean seat and a straight arm, the 87mm fiber glass spring holds the scraper in contact and keeps the pressure repeatable run to run.

The spring ships by FedEx, UPS or DHL. Origin country is China. Packing and customisation are not stated here, so ask before you assume either. With your enquiry, send the part number 3-601-06-0341, the GFK L87 marking, the 87mm length, the machine model and a photo of the old spring in its seat.

What the specification fixes, and what it leaves to the machine:

• Spring pressure on the scraper — The L=87mm spring length sets how the scraper spring sits in its seat and how it loads the scraper arm on the Homag head.
• Part number match — The 3-601-06-0341 number on the spring is the check that ties the replacement to the Homag machine you are working on.
• GFK L87 marking — GFK L87 appears on the part, giving a second marking to compare with the old spring before you fit the new one.
• Fiber glass construction — Fiber glass is the spring material, and the part is built as a scraper spring for woodworking machine use on Homag equipment.
• Seat and arm check — Inspect the spring seat and scraper arm first, because wear or a bend there will change how the 87mm spring behaves in the head.
• Chip pocket condition — Clear the chip pocket around the spring seat, since packed chips stop the fiber glass spring from moving through its full travel.
• Spring replacement point — Fit a new spring when the scraper stops holding contact, and match the 3-601-06-0341 number and 87mm length to the old one.

What changes on the shop floor when the right part goes back in:

• Restores scraper contact. A fresh 87mm fiber glass spring puts pressure back on the scraper arm, so the scraper holds the surface instead of riding or chattering through the cut on the Homag machine.
• Match by number, not guesswork. The 3-601-06-0341 number and the GFK L87 marking give you two checks against the old spring, which cuts the chance of fitting the wrong part.
• Fiber glass holds its job. Fiber glass is the spring material, chosen for a scraper spring that flexes in the head, so the part keeps working as a spring rather than deforming in service.
• One length to check. At L=87mm the spring has a single length to measure against your old part, which makes the fit check quick at the bench before ordering.
• Small part, short downtime. A scraper spring is a small spare, so swapping the 3-601-06-0341 part takes little time once the correct spring is on hand at the machine.
• Carrier choice at dispatch. FedEx, UPS and DHL are the shipment options, so you can pick the carrier that fits your receiving schedule and how urgent the spare is.

Check the number and length against your old spring: 3-601-06-0341 and L=87mm. The spring is made for Homag machines, but the sure check is pulling your existing spring and comparing the 3-601-06-0341 number, the GFK L87 marking and the 87mm length before you order.

The length is L=87mm. That is the size given for this fiber glass scraper spring, part number 3-601-06-0341, marked GFK L87. Measure your old spring and compare it with the 87mm figure before fitting.

Fiber glass. The scraper spring is built from fiber glass, which is the material given for the 3-601-06-0341 part. It is supplied as a woodworking machine spare for Homag equipment.

Read the number off the old spring and match it to 3-601-06-0341. The GFK L87 marking is a second check. If both match your old spring and the length reads 87mm, you have the right part to compare against.

Look at the spring seat and the scraper arm. Wear at the seat, a bent arm or packed chips in the pocket will spoil the spring's action even with a new 87mm spring, so clean and check those points first.

By FedEx, UPS or DHL. Those are the shipment options for this part. Ask about packing and any customisation when you enquire, since neither is stated for the 3-601-06-0341 spring.

Origin country is China. The part is the 3-601-06-0341 fiber glass scraper spring, GFK L87, at L=87mm, supplied as a woodworking machine spare for Homag machines.

Send the part number 3-601-06-0341, the GFK L87 marking, the 87mm length, your machine model and a photo of the old spring in its seat. That lets the supplier check the request against the part before dispatch.