100 125 150mm PU Hose Sweep Up Pipe Dust Collection Soft Pipe Woodworking

PU hose for dust collection on woodworking machinery, supplied in 100mm, 125mm and 150mm diameters with 0.63mm PU wall. Rolls come in 10m/roll or 15m/roll, and the same hose is also available in φ50mm, φ60mm, φ63mm, φ75mm, φ80mm and φ200mm. To confirm fit, measure the outside diameter of your machine's sweep-up port and match it to one of the three sizes before ordering. Shipment is by sea. Send your diameter and roll length with the enquiry so the right hose is quoted.

Dust builds up at the sweep-up port when the hose on the machine is too stiff to route or has worn thin at the bends. A collapsed or kinked run chokes airflow right where the chips are picked up, so the port keeps spilling dust onto the floor and into the air around the cutter.

This is a PU hose, made of PU, with a 0.63mm wall. Three diameters are offered: 100mm, 125mm and 150mm, on 10m/roll or 15m/roll. Other available sizes include φ50mm, φ60mm, φ63mm, φ75mm, φ80mm and φ200mm. To confirm fit, measure the outside diameter of the sweep-up port and the spigot on your machine, then pick the matching hose size.

Check how the hose leaves the port and where it bends on the way to the collector. PU at 0.63mm stays flexible enough to follow a curve rather than fight it, which keeps the run open instead of pinching at the machine frame. Confirm the port clamp or collar grips the hose end without crushing the wall.

Rolls are supplied at 10m/roll or 15m/roll, and shipment is by sea. If your machine takes a size outside 100mm, 125mm and 150mm, the φ50mm, φ60mm, φ63mm, φ75mm, φ80mm and φ200mm options are available. Send the port diameter, the roll length you need and the quantity when you enquire.

What the specification fixes, and what it leaves to the machine:

• Sweep-up port connection — Hose in 100mm, 125mm and 150mm diameters covers the common sweep-up port sizes on woodworking machines, so you can match the port instead of adapting it.
• Bend routing at the frame — PU construction lets the hose follow curves around the machine frame, keeping the run open where a rigid pipe would need extra elbows.
• Wall thickness at the wear point — The 0.63mm PU wall is the contact surface at the port and at every bend, so it is the first place to inspect for thinning.
• Roll length for long runs — Supplied at 10m/roll or 15m/roll, so a single roll covers a full run from the sweep-up point to the collector without a joint.
• Non-standard port sizes — Also available in φ50mm, φ60mm, φ63mm, φ75mm, φ80mm and φ200mm, covering smaller pickup points and larger main runs on the same machine.
• Clamp grip at the hose end — Check that the port clamp or collar grips the hose end without crushing the 0.63mm wall, which keeps the bore round at the connection.
• Chip pickup at the cutter — A hose matched to the port diameter keeps the pickup point pulling chips straight off the cut instead of letting them settle on the table.

What changes on the shop floor when the right part goes back in:

• Match the port, not the pipe. With 100mm, 125mm and 150mm options, you measure the sweep-up port once and order the size that clamps straight on, without building an adapter.
• Flex where the machine needs it. PU construction lets the hose bend around the frame and the sweep-up arm, so the run stays open through curves instead of pinching at the corners.
• One roll, one run. At 10m/roll or 15m/roll, a single length reaches from the pickup point to the collector, so there is no joint in the middle to leak or pull apart.
• Sizes beyond the three main ones. φ50mm, φ60mm, φ63mm, φ75mm, φ80mm and φ200mm are also available, so smaller pickup points and larger runs can come from the same supply.
• A known wall to inspect. The 0.63mm PU wall gives you one figure to check at each bend and at the port, so worn hose is found before it splits and drops dust.
• Keep the pickup pulling. A hose that fits the port and stays round under the clamp keeps airflow at the pickup point, so chips go into the collector rather than onto the floor.

Measure the outside diameter of the sweep-up port and the spigot, then match it to 100mm, 125mm or 150mm. If the port measures outside those three, check the φ50mm, φ60mm, φ63mm, φ75mm, φ80mm and φ200mm options before ordering.

It is PU hose with a 0.63mm PU wall. That wall thickness is the figure to check at the port and at each bend when you inspect for wear.

Rolls are supplied at 10m/roll or 15m/roll. Tell us which length suits your run so the roll covers the distance from the pickup point to the collector without a joint.

Yes. Other available sizes are φ50mm, φ60mm, φ63mm, φ75mm, φ80mm and φ200mm. Send the port diameter you measured and we will quote the matching size.

It fits over the sweep-up port and is held by the machine's clamp or collar. Check that the clamp grips the hose end without crushing the 0.63mm wall, so the bore stays round at the connection.

Yes, PU construction lets it follow curves around the frame and the sweep-up arm. Route it so the bends are gentle and the run stays open rather than pinched.

Shipment is by sea. Put every diameter and roll length you need on one enquiry so the whole order can go on a single shipment.

Send the port diameter you measured, the roll length you need (10m/roll or 15m/roll), the quantity, and any of the other sizes you want quoted.