0820037202 24V DC Pneumatic Valve ELEK AVENTICS For Homag Machine

The 0820037202 is a 24V DC pneumatic valve from ELEK AVENTICS, built to fit Homag woodworking machines. It handles pneumatic control on the machine, running on a DC current supply. The valve is packed in a standard carton box. Before ordering, confirm your Homag machine carries the 0820037202 part number in its pneumatic circuit, and check the valve position and port layout against the old unit you are replacing. Send the machine model and the part number stamped on the failed valve so the fit is checked before shipment.

When a Homag machine loses pneumatic action on one circuit, the valve feeding that circuit is often the first place to look. The 0820037202 is the replacement for that position, so the machine can return to normal cycling without a workaround.

The 0820037202 is a 24V DC pneumatic valve carrying the ELEK AVENTICS name. It fits Homag machines in the woodworking industry. To confirm the fit, read the part number off the valve you are removing and match it to 0820037202, then compare the port layout and coil connection on the old and new units before you pull anything apart.

Check the valve position on the machine and how the coil is wired before removal. The 24V DC current supply must match what the machine delivers to that valve position. Note which ports feed which line, because getting a line back on the wrong port sends air the wrong way and the machine will not cycle as it should.

Each valve ships in a standard carton box. Include the Homag machine model and the part number from the old valve with your enquiry, plus a photo of the valve in place if you can. That lets the fit and the 24V DC supply be checked against your machine before the order is packed.

What the specification fixes, and what it leaves to the machine:

• Circuit replacement position — Fits the Homag machine pneumatic circuit position that takes the 0820037202 valve, so you swap the failed unit rather than rework the line.
• Coil supply match — Runs on a 24V DC current supply, matching the DC valve positions on Homag machines so the coil wiring stays as built.
• Brand identification — Carries the ELEK AVENTICS name on the valve, giving you a part number to check against the unit coming off the machine.
• Part number marking — The 0820037202 number identifies this valve, so match it to the marking on the old unit before ordering a replacement.
• Woodworking duty — Built for woodworking industry use, where dust and constant cycling put wear on pneumatic valves through the shift.
• Coil connection check — Compare the coil plug on the old valve with the new one before fitting, so the 24V DC connection goes back on correctly.
• Port layout check — Lay the old and new valves side by side and match port positions before removal, keeping each air line on its original port.
• Line marking before removal — Tag each air line as you take it off, so the 0820037202 goes back with every line on the port it came from.

What changes on the shop floor when the right part goes back in:

• Swap the failed position, not the whole block. Matching the 0820037202 number to the valve on your Homag machine means one position gets replaced and the rest of the pneumatic block stays as it is.
• Keeps the DC wiring as built. A 24V DC valve matches the supply the machine already runs to that position, so the coil connection goes back the way it came off.
• Faster fault isolation. When one circuit stops shifting, a known part number lets you confirm the valve is the right replacement before the machine sits idle any longer.
• Fewer wrong-port comebacks. Matching port layout to the old unit before removal means each air line returns to its original port and the circuit cycles correctly on the first start.
• Built for woodworking conditions. The valve is intended for woodworking industry use, where dust and repeated cycling are part of the daily duty on Homag machines.
• Checked before it ships. Send the machine model and the old valve part number with your enquiry, and the fit and 24V DC supply are checked against your machine first.

Match the part number on the valve you are removing to 0820037202. Then compare the port layout and coil connection on the old and new units, and send your machine model with the enquiry so the fit is checked before shipping.

It runs on 24V DC. Check that the supply the machine delivers to that valve position is 24V DC before you connect the new unit.

The valve carries the ELEK AVENTICS name. The part number to match is 0820037202, which is the number to compare against the unit coming off the machine.

Each valve ships in a standard carton box. Keep the box and packing until the valve is fitted and the circuit is cycling again.

Send the Homag machine model, the part number from the old valve and, if possible, a photo of the valve in place. That lets the fit and the 24V DC supply be checked against your machine.

Marking the lines first is the safer route. Tag each line as it comes off so every line returns to its original port on the 0820037202 and the circuit cycles correctly.

Check the 24V DC supply to the coil and the air feed to that position. A valve that will not shift usually points at the coil supply or the air line, so test those before pulling the valve again.

It is intended for the woodworking industry and fits Homag machines. Confirm the part number against your machine before ordering for any other use.