150mm Z Axis Maglev Side Drilling Device Drilling Parts For Edgebanding Machine

The XEX4ZXK-500 is a Shunhongyu Maglev Side Drilling Device for edgebanding machines, with a 150mm Z-axis travel, 260mm Y-axis travel and 100mm X-axis travel. It carries a photoelectric switch, linear guides, vacuum hood, spindle motor, maglev module, servo motors, ball screw, oil separator, silent chains and base. To confirm fit, match these travels and the XEX4ZXK-500 model number to your edgebander's side-drilling station before ordering.

Side drilling on an edgebander often drifts when the Z-axis cannot hold position through the cycle. The XEX4ZXK-500 addresses that wear point with a maglev module driving 150mm of Z-axis travel, so the drill head returns to the same height cut after cut.

This is the Shunhongyu Maglev Side Drilling Device, model XEX4ZXK-500, built as parts for an edgebander. Travels are 150mm on Z, 260mm on Y and 100mm on X. The assembly includes a photoelectric switch, linear guides, vacuum hood, spindle motor, maglev module, servo motors, ball screw, oil separator, silent chains and base.

Check the mounting face and the 100mm X-axis travel against the space at your side-drilling station before installation. The vacuum hood sits at the drilling point to collect chips, and the photoelectric switch ties into the machine's position sensing. Because the maglev module carries the Z-axis, the 150mm stroke runs without the mechanical slack that builds up in a worn screw-driven slide.

Packing and customisation details are not stated here, so send those questions with your enquiry. Include your edgebander make and model, the existing side-drilling unit's model number if visible, and the three travels you need: 150mm Z, 260mm Y, 100mm X. Photos of the mounting area and the old unit help confirm that XEX4ZXK-500 is the correct replacement before you order.

What the specification fixes, and what it leaves to the machine:

• Z-axis travel for drill height — The maglev module drives 150mm of Z-axis valid itinerary, which sets the working stroke for side-drilling height changes on the edgebander.
• Y-axis travel for horizontal positioning — A 260mm Y-axis valid itinerary covers the horizontal movement range needed to place side-drilling holes along the panel edge.
• X-axis travel for in-and-out feed — The 100mm X-axis valid itinerary controls how far the drilling unit advances toward the panel during the side-drilling cycle.
• Photoelectric switch for position sensing — A photoelectric switch is included in the assembly, giving the machine a position signal at the drilling station during each cycle.
• Linear guides for slide accuracy — Linear guides carry the moving sections, keeping the drill head on its path through the 150mm Z-axis stroke as the unit cycles.
• Vacuum hood at the drilling point — The vacuum hood sits at the drill point to collect chips, reducing buildup around the side-drilling area during production runs.
• Spindle motor for drilling drive — A spindle motor turns the drill, and its mounting on the unit keeps the drive aligned with the side-drilling axis on the edgebander.

What changes on the shop floor when the right part goes back in:

• Maglev Z-axis holds drill height. The maglev module carries the 150mm Z-axis travel, so the drill head returns to the same height instead of drifting with wear in a screw-driven slide.
• Three travels cover side-drilling moves. With 150mm on Z, 260mm on Y and 100mm on X, the unit covers the positioning range for side-drilling holes without adding a separate slide.
• Parts set reduces separate sourcing. The assembly includes the photoelectric switch, linear guides, vacuum hood, spindle motor, maglev module, servo motors, ball screw, oil separator, silent chains and base.
• Vacuum hood keeps the drill point clear. Chips are collected at the drilling point by the vacuum hood, which cuts buildup around the side-drilling area between cleaning stops.
• Linear guides keep the stroke on path. Linear guides carry the moving sections through the 150mm Z-axis stroke, so the drill head tracks its path as the unit cycles.
• Servo control matches machine commands. Servo motors on the axes let the edgebander's control system command the 150mm, 260mm and 100mm travels for each drilling position.
• Model number makes fitment check direct. Matching XEX4ZXK-500 and the three travels to your edgebander's side-drilling station confirms the replacement before you order.

Match the model number and travels to your machine. Check that your edgebander's side-drilling station uses the XEX4ZXK-500 and that 150mm Z, 260mm Y and 100mm X travels suit your panel work.

The Z-axis valid itinerary is 150mm, the Y-axis valid itinerary is 260mm and the X-axis valid itinerary is 100mm. These are the movement ranges built into the unit.

The parts set includes a photoelectric switch, linear guides, vacuum hood, spindle motor, maglev module, servo motors, ball screw, oil separator, silent chains and base. Confirm your required scope with the supplier.

Send your edgebander make and model plus photos of the existing side-drilling unit. The three travels and the XEX4ZXK-500 model number are the key checks against your machine.

The maglev module drives the 150mm Z-axis travel. It carries the drill head through its height changes on the side-drilling station.

Packing and customisation details are not stated here. Ask the supplier directly and include your requirements with your enquiry.

Include your edgebander make and model, the old unit's model number if visible, the travels you need and photos of the mounting area. This lets the supplier confirm XEX4ZXK-500 against your machine.

Yes, the vacuum hood is included in the parts set. It sits at the drilling point to collect chips during side-drilling.