Yellow Feeding Roller Rubber Wheel Aluminum Core For Woodworking Double Side Planer Machine

A yellow feeding roller rubber wheel with an aluminum core, sized 120x30x50mm or 140x35x50mm, for woodworking double-side planer machines. The rubber surface grips the board while the aluminum core holds the wheel on the feed shaft. Check your existing roller's dimensions and shaft fit before ordering. Both sizes are available under SKU 140x35x50mm and 120x30x50mm. Send the machine model and the old wheel's measurements with your enquiry so the correct size is supplied for your planer.

When boards slip or feed unevenly on a double-side planer, the feeding roller is often the first place to check. Worn or glazed rubber loses grip, and the board can hesitate or skew. Replacing the roller restores consistent contact between the wheel and the timber surface.

This press wheel is a rubber wheel with an aluminum core, yellow in color, and comes in two sizes: 120x30x50mm and 140x35x50mm. It fits woodworking double-side planer machines as a feeding roller. To confirm fit, measure your existing wheel's outer diameter, width, and bore, and compare with these sizes.

Check the shaft diameter and keyway or mounting method on your machine before installation. The aluminum core must seat squarely on the shaft so the rubber runs true. A wheel that wobbles will wear unevenly and mark the board. Tighten according to your machine's manual and spin the roller by hand to check alignment before running stock.

Supply is straightforward: the wheel is packed as a single spare part, and customisation is not stated. When enquiring, include the machine model, the old wheel's dimensions (outer diameter x width x bore), and the quantity needed. Photos of the old part and shaft help confirm the size before you commit to an order.

What the specification fixes, and what it leaves to the machine:

• Board grip on the infeed — Yellow rubber surface contacts the timber directly, giving the feeding roller traction to pull boards into the planer cut.
• Core strength at the shaft — Aluminum core carries the mounting load, so the rubber wheel stays round and true on the feed shaft.
• Two size options — Available in 120x30x50mm and 140x35x50mm to match different planer feed setups and existing wheel dimensions.
• Wear part replacement — Rubber wears with use; replacing the complete wheel with aluminum core restores feed grip without modifying the machine.
• Color for visibility — Yellow color makes the feeding roller easy to spot during inspection, so worn or damaged rubber is noticed sooner.
• Double-side planer fit — Designed as a press wheel for woodworking double-side planer machines, sitting in the feed path to hold stock down.
• Rubber-to-core bond — Rubber is bonded to the aluminum core to keep the wheel together under the push and pull of feeding boards.
• Bore and width check — Confirm the 50mm bore and the 30mm or 35mm width against your shaft and mounting space before ordering.
• Spare part stock — Keep a spare feeding roller on hand so a worn wheel does not stop the planer during a production run.

What changes on the shop floor when the right part goes back in:

• Restores feed consistency. A fresh rubber surface grips the board again, so stock moves through the double-side planer at a steady rate instead of slipping or hesitating.
• Protects board finish. A true-running wheel with an aluminum core avoids wobble that can mark the timber, helping keep planed surfaces clean and reducing rework.
• Fits two common sizes. With 120x30x50mm and 140x35x50mm options, you can match the existing wheel on your planer and avoid machine modification.
• Easy to identify wear. The yellow rubber shows glazing and flat spots clearly during routine checks, so you can plan replacement before feed quality drops.
• Cuts troubleshooting time. When feed problems start, swapping the feeding roller is a direct fix; a spare wheel on the shelf gets the planer running again quickly.
• Core holds its shape. Aluminum resists the bending that can distort an all-rubber wheel, keeping the press wheel round and the feed path stable over time.
• Clear enquiry process. Send the machine model and old wheel dimensions with your enquiry; the 50mm bore and width are checked against your shaft before supply.
• It fits the machine you already run. The rubber wheel is made for woodworking machines, so it returns to the same shaft, bracket or spindle without re-machining the mounting.

Measure the old wheel's outer diameter, width, and bore. Compare those numbers with 120x30x50mm and 140x35x50mm, and send the machine model with your enquiry.

It fits woodworking double-side planer machines as a feeding roller. Check that your machine uses a press wheel of the same dimensions and mounting style.

It is a rubber wheel with an aluminum core. The yellow rubber provides grip on the board, and the aluminum core mounts on the feed shaft.

Those are the wheel dimensions: 120mm outer diameter, 30mm width, and 50mm bore. Confirm each measurement against your shaft and mounting space.

Slide the wheel onto the feed shaft, seat the aluminum core squarely, and tighten according to your machine's manual. Spin by hand to check for wobble.

The stated use is for woodworking double-side planer machines. For other machines, confirm shaft diameter, bore, and wheel width before ordering.

Send the machine model, the old wheel's outer diameter, width, and bore, the quantity needed, and photos of the old part and shaft if possible.

It is supplied as a single spare part. Customisation and packing details are not stated, so ask about your specific requirement when you enquire.