1250mm Table Saw Ruler Carpentry Aluminum Alloy Fence Woodworking Machinery Tool

This is a 1250mm table saw ruler with an aluminum alloy fence, a spare part for table saws used to set and hold a cut line along the table. The ruler runs 125cm and the fence is aluminum alloy, so it resists corrosion and stays straight in a shop environment. Before ordering, confirm your table saw's fence mounting points and the 1250mm length your table needs. The 125cm length suits large sheet goods and long rips. Sea shipment is recommended because of the long length.

When a table saw fence drifts or the scale wears off, rips come out tapered and the operator starts measuring every cut twice. A worn or bent fence rail is the usual cause: the stock no longer bears against a straight edge, so the blade follows the error.

This is a 1250mm table saw ruler supplied as a spare part, with an aluminum alloy fence and a stop sawing ruler. The 125cm length covers long rips and sheet goods. It fits table saws that use a bolt-on fence rail. To confirm fit, measure your existing rail mounting holes and the 1250mm span against your table.

Mounting is a bolt-on job: the fence rail fixes to the table edge at the existing holes, and the ruler scale runs along the 1250mm length. Check that the rail sits parallel to the blade before tightening. Once set, the aluminum alloy profile gives a straight bearing face for the fence and a readable scale for repeat cuts.

Supply is straightforward: the ruler ships as a 1250mm aluminum alloy part, and sea shipment is recommended because of the long length. No customisation or packaging options are stated. Send your table saw model, the mounting hole spacing, and the 1250mm dimension you need with your enquiry so the fit can be checked before ordering.

What the specification fixes, and what it leaves to the machine:

• Rip width reference — The 1250mm ruler scale runs the full 125cm length, giving a fixed measuring reference for ripping stock on the table saw.
• Fence bearing face — An aluminum alloy fence provides a straight edge for the workpiece to bear against during rips and crosscuts.
• Stop sawing setup — The stop sawing ruler lets the operator set a repeat stop position along the 1250mm scale for batch cuts.
• Long stock support — At 125cm, the ruler spans long rips and sheet goods, so the scale stays usable on large workpieces.
• Corrosion resistance — Aluminum alloy resists corrosion in shop environments, so the scale surface and profile hold up to humidity and dust.
• Straightness under load — The aluminum alloy profile resists bending and warping, keeping the fence edge straight when stock is pushed against it.
• Bolt-on mounting — The fence rail fixes at the table edge mounting holes; check hole spacing and the 1250mm span before ordering.
• Parallel alignment check — Set the rail parallel to the blade before tightening, so the fence reads true along the 1250mm scale.
• Spare replacement — Supplied as a table saw spare part, the ruler replaces a worn or bent fence rail without changing the saw.

What changes on the shop floor once the unit is in place:

• Cuts stop drifting. A straight aluminum alloy fence gives the stock a fixed bearing face, so rips follow the 1250mm scale instead of wandering with a worn rail.
• Fewer re-measures. The 1250mm ruler scale stays on the machine, so the operator reads the fence position directly and skips laying a tape on every cut.
• Handles long rips. The 125cm length covers long stock and sheet goods, so the fence reference runs the full rip instead of stopping short.
• Stays straight in the shop. Aluminum alloy resists bending and warping, so the fence edge holds its line through daily pushing of stock against it.
• Resists shop humidity. Aluminum alloy resists corrosion, so the scale and profile do not rust or flake in a damp workshop and stay readable.
• Repeatable batch cuts. The stop sawing ruler sets a repeat position along the 1250mm scale, so batch parts come out at the same width.
• Simple spare swap. The ruler mounts at the existing table edge holes, so a worn rail is replaced without modifying the saw or its fence.

Check your fence rail mounting holes and the 1250mm span against your table before ordering. The ruler fits table saws that use a bolt-on fence rail; send your saw model and hole spacing to confirm.

The ruler is 1250mm long, which is the same as 125cm. That length covers long rips and sheet goods on the table.

The fence and ruler are aluminum alloy. That material resists corrosion and keeps the profile straight under stock pressure.

The part is supplied as a stop sawing ruler along the 1250mm scale. No separate stop hardware beyond the ruler is stated.

The fence rail fixes at the table edge mounting holes. Set the rail parallel to the blade, then tighten, so the 1250mm scale reads true.

No customisation is stated for this 1250mm ruler. Send your required dimensions with the enquiry and the fit can be checked against the standard part.

Sea shipment is recommended because of the 1250mm length. That keeps freight practical for a long aluminum alloy part.

Send your table saw model, the mounting hole spacing, and the 1250mm dimension you need. That lets the fit be checked before you order.