2003651713 Pneumatic Cylinder Seal Kit For 1-003-65-5263 Woodworking Tool

When the pneumatic cylinder on a Holzma HPP, HPL or HKL saw starts leaking air at the rod or end cap, clamp pressure drops and cycle times stretch out. Replacing the seals is the usual fix. This kit covers the 1-003-65-5263 cylinder, so the machine can go back into production without swapping the whole cylinder.

The kit is a set of rubber seals for the 1-003-65-5263 pneumatic cylinder, sold under Homag part numbers 2-003-65-1713 and 2003651713. Buyers confirm the fit by reading the cylinder identification on the machine and matching it to 1-003-65-5263, then checking the seal positions against the kit before installation.

Pull the cylinder, note the order of the old seals as they come out, and fit the new ones in the same positions. Rubber seals need a clean bore and light lubrication at assembly. Done this way, the cylinder holds pressure again and the clamp repeats without drift.

Kits ship by DHL, FedEx, UPS and similar carriers. Send the machine model, the cylinder number 1-003-65-5263 and the part number 2-003-65-1713 with your enquiry so the correct kit is picked. If you need other Holzma HPP, HPL or HKL parts, list them in the same message.

What the specification fixes, and what it leaves to the machine:

• Cylinder fitment — Seals are sized for the 1-003-65-5263 pneumatic cylinder used on Holzma HPP, HPL and HKL series woodworking machines.
• Part number match — The kit is identified by Homag part numbers 2-003-65-1713 and 2003651713, which you can check against the machine documentation.
• Seal material — Seals are made from rubber, chosen for elasticity and wear resistance in pneumatic service.
• Leak repair point — Fits the rod and end-cap seal positions where air leaks show up as pressure loss on the clamp.
• Kit contents check — Compare the seals in the kit with the old ones as they come out of the cylinder before reassembly.
• Bore preparation — Clean the cylinder bore and remove old seal residue before fitting new rubber seals.
• Assembly lubrication — Light lubrication at assembly helps the rubber seals seat without rolling or pinching in the bore.
• Clamp repeatability — Fresh seals restore clamp holding pressure so panel positioning repeats from cycle to cycle.
• Downtime planning — Keep a kit on the shelf so a leaking cylinder does not stop the saw while you wait for parts.
• Cross-reference — Search terms Holzma HPP, HPL and HKL seal 2-003-65-1713 help you match this kit to your machine.

What changes on the shop floor once the unit is in place:

• Rebuild instead of replace. A leaking 1-003-65-5263 cylinder usually needs seals, not a new cylinder. This kit lets you restore the existing unit and keep the original mounting and stroke.
• Pressure comes back. New rubber seals close the leak path at the rod and end cap, so clamp pressure holds through the cut instead of fading between cycles.
• One kit, one job. The set covers the seal positions for the 1-003-65-5263 cylinder, so you are not ordering individual seals and hoping each one matches.
• Number-first ordering. Matching 2-003-65-1713 and 2003651713 against your documentation removes guesswork before the kit leaves the shelf.
• Shelf stock pays off. A spare kit on hand means a leaking cylinder is a planned repair, not a stopped saw waiting on a DHL, FedEx or UPS delivery.
• Rubber that moves. Rubber seals flex with the cylinder stroke and return to shape, which keeps the rod seal tracking the rod through repeated cycles.
• Fits three saw families. The same kit serves Holzma HPP, HPL and HKL machines that use the 1-003-65-5263 cylinder, so one stock item covers mixed saw lines.

It fits the 1-003-65-5263 pneumatic cylinder. Check the cylinder identification on your Holzma HPP, HPL or HKL machine against that number before ordering.

Match the cylinder number 1-003-65-5263 and the part number 2-003-65-1713 to your machine documentation. If both match, the kit is the one for that cylinder.

The seals are rubber. That material is what the kit is built from, and it is suited to the flexing and pressure of a pneumatic cylinder.

Replace them when the cylinder leaks air or the clamp stops holding pressure. A visible leak at the rod or end cap is the usual sign the seals are worn.

Remove the cylinder, note the order of the old seals, clean the bore and fit the new seals in the same positions with light lubrication. Reassemble and test for leaks.

Yes. State the quantity you need with your enquiry, along with the cylinder number 1-003-65-5263 and part number 2-003-65-1713.

Orders ship by DHL, FedEx, UPS and similar carriers. Give a delivery address and contact number with your enquiry so the shipment can be arranged.

Send the machine model, the cylinder number 1-003-65-5263, the part number 2-003-65-1713 and the quantity. Add any other Holzma HPP, HPL or HKL parts you need in the same message.