Pneumatic Flat Scraper for Woodworking Edgebanding Machine Flat Scraping Device

Glue lines and proud edgebanding show up after trimming, especially on flat panel edges where the scraper station does the final clean-up. A worn or misaligned flat scraper leaves ridges, tear-out or smeared adhesive that send panels to rework.

The edgebander flat scraper is a pneumatic unit measuring 190mm in length, 100mm in width and 62mm in depth, branded Shunhongyu. It mounts in the flat scraping device of a woodworking edgebanding machine. To confirm fit, compare the 190*100*62mm envelope and the pneumatic port position with the space and connections on your machine, and match the mounting pattern to the old unit.

Check the mounting face and the pneumatic supply line before installation. The scraper is air-controlled, so the supply must reach the unit and the mounting bolts must seat flat against the machine frame. Once seated, the flat scraper runs against the edge under air pressure, and a square mount keeps the scraping face parallel to the panel edge.

Supply comes as the scraper unit in the 190*100*62mm size. No packing, customisation, MOQ or lead time is stated here, so confirm those with the supplier. With an enquiry, send the edgebander make and model, a photo of the current flat scraper and its mounting, the pneumatic connection type, and the panel edge problem you are trying to solve.

What the specification fixes, and what it leaves to the machine:

• Flat scraping station fit — Fits the flat scraping device on a woodworking edgebanding machine, where the 190mm length runs along the edge to clean the band.
• Pneumatic control — Air-operated control lets the scraper follow the edge under pressure instead of relying on a fixed mechanical spring or manual setting.
• Overall size — The 190*100*62mm envelope gives buyers a direct size check against the space left by the old scraper.
• Length reference — At 190mm long, the scraper spans the edge contact area; compare this with the old unit before ordering.
• Width reference — The 100mm width sets how much of the mounting face contacts the machine; check clearance around the station.
• Depth reference — A 62mm depth defines how far the unit sits from the mounting face; confirm this against the frame and air line.
• Brand and origin — Shunhongyu brand, made in China; use the brand and the 190*100*62mm size when matching against the existing part.
• Mounting check — Before fitting, confirm the bolt pattern and the pneumatic port line up with the flat scraping device on your edgebander.
• Wear point — The scraping face is the wear point; inspect it for nicks or rounding that would leave marks on the edgebanded panel.

What changes on the shop floor once the unit is in place:

• Cleaner edge off the scraper. A flat scraper set square to the edge removes glue lines and proud banding in one pass, cutting the hand clean-up that slows the line.
• Air control suits repeat runs. Pneumatic operation keeps the scraping force consistent from panel to panel, so the edge finish does not drift between the first and last piece.
• Size check before you buy. The 190*100*62mm envelope lets you compare the new unit with the old one on the bench, reducing the chance of a return.
• One station, less rework. Replacing a worn flat scraper in the flat scraping device restores the final edge clean-up, so fewer panels go back for re-trimming.
• Known brand and origin. Shunhongyu brand from China gives buyers a clear reference when ordering a replacement or matching against the existing scraper.
• Simple mounting check. Comparing the mounting face and air port against the machine frame takes minutes and confirms whether the unit will seat correctly.
• Clear enquiry path. Sending the machine model, a photo of the old scraper and the air connection type lets the supplier check fit before you commit.

Check the 190*100*62mm size and the mounting pattern against your flat scraping device first. Send the machine make and model and a photo of the old unit so the fit can be confirmed before ordering.

It removes excess adhesive and levels the edgebanded surface at the flat scraping station. The air control keeps the scraping face against the edge during the pass.

The unit measures 190mm long, 100mm wide and 62mm deep. Compare these with the space and mounting face on your machine.

Yes, the scraper is pneumatically controlled. Confirm the air supply line and connection type at the flat scraping station before installation.

Shunhongyu brand, made in China. Use the brand and the 190*100*62mm size when matching against the existing scraper.

Seat the mounting face flat against the machine frame and connect the pneumatic line. Check that the scraping face sits square to the panel edge before running production.

Send the edgebander make and model, a photo of the current flat scraper and its mounting, the pneumatic connection type, and the edge problem you need to fix.

Those details are not stated here. Ask the supplier directly and include the machine model and the 190*100*62mm size in your request.